manualshive.com logo in svg

Matsusada R4G Series, Инструкция по эксплуатации

Поделиться
Скачать
Matsusada R4G Series Скачать руководство пользователя страница 26

4  Normal  Operation 

 

 

18

 

R4G/R4GE series 

 

LOCK 

OCP 

SET 

OVP/ 

CV 

CC 

V 

A 

OUTPUT 

REMOTE 

FINE 

FINE switch 
 

 

Pressing the [FINE] switch on the front panel will  cause the voltmeter/ammeter to brightly display 

the digit whose setting value can be changed. 

Pressing the [FINE] switch on the front panel will  cause the voltmeter/ammeter to brightly display 

the digit whose setting value can be changed. When the switch is pressed in displaying the monitor 

screen while the output is ON, the changeable digits in the monitor display are brightly displayed. 

When the switch is pressed during the OVP/OCP setting screen displayed, the changeable digits of 

the OVP/OCP set voltage/current value are brightly displayed. 

 

Pressing  the  [FINE]  switch  moves  the  digit  (the  brightly  lit  digit)  where  the  setting  value  can  be 

changed. 

 

Turn the voltage or current setting dial to adjust the setting value of the specified digit. 

 

When  the  [OUTPUT  ON/OFF]  switch  is  "ON"  (OUTPUT  LED  is  lit),  note  that  both  voltage  and 

current have been output, so be careful to avoid electric shock. 

 

 
 
 
 
 
 
 
 
 
 
 

 

The  digit  in  which  the  set  value  is  changeable  is 
brightly displayed.

 

Press FINE

 

VOLTAGE

 

 

 

CURRENT

 

 

 

Output voltage setting 
(Voltage setting dial) 
 
Output current setting 
(Current setting dial) 

One of preset, monitor, or OVP/OCP is displayed.

 

Содержание R4G Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды