Matsusada R4G Series Скачать руководство пользователя страница 13

Страница: 13 / 60

2 Before Use

R4G/R4GE series

Before Use

2-1

Unpacking

After unpacking the box, check that the following accessories are supplied with the product. If the

accessories are different, missing, or broken, please contact us immediately.

□ Instruction manual

㍶

□ AC input code, three-core, single-phase

1 pc

□ MIL 26-pin male connector*

1 pc

□ MIL 26-pin semi-cover*

1 pc

□ CO-M cable, 2m long*

1 pc

When the -LGmb option is installed.

□ CO-OPT cable*

1 pc

When the -LGob option is installed.

only for the R4G series

2-2

Initial Inspection

After unpacking and before wiring input and output, check the product for any abnormalities.

Check the front panel, rear panel, and chassis for scratches, dents, or other signs of shock from

transportation or handling.

If you find any abnormalities, please contact the carrier and us.

2-3

Precautions for handling



For the input voltage, check this instruction manual and the indication on the rear panel of the unit

itself.
Do not provide any voltage out of the specifications. Doing so may result in fire or malfunction.



Do not open or remove the case cover of the unit. Doing so may result in electric shock or

malfunction.



When changing the system, do it after turning off the power of all devices that
make up the system.



Generally, connect one of the output terminals, +/-, to the GND terminal with a short bar.



Firmly Insert the AC input cord plug into an outlet.



The heat sink may become hot. Do not touch as it may cause burns.

Содержание R4G Series





























































Результаты поиска

Содержание R4G Series

Отзывы:

Бренды по названию

Популярные бренды

Matsusada R4G Series, Инструкция по эксплуатации

Результаты поиска

Содержание R4G Series

Отзывы:

Бренды по названию

Популярные бренды