Matsusada R4G Series Скачать руководство пользователя страница 28

Страница: 28 / 60

4 Normal Operation

R4G/R4GE series

4-6

Power Failure Protection

This product has a built-in function to turn off the output when the input power source is recovered after

power failure.

A power failure occurred in operation, the unit keeps turning off the output even if it is recovered

afterward.

In order to turn on the output again, once turn off the [OUTPUT ON/OFF] switch and then turn it on

again.

If you do not use this function, set "PFP" to "OFF" in the startup menu.

If you do not use this function, the unit returns to the state just before a power failure occurred when the

input power source recovers after a power failure occurred in operation, or the [POWER ON/OFF] switch

is turned on. (If a power failure occurs while the [OUTPUT ON/OFF] switch is ON, the output will turn on

after recovery. If a power failure occurs while the [OUTPUT ON/OFF] switch is OFF, the output will keep

turning off after recovery.)

The Power Failure Protection (PFP) function can be set to ON (enabled) or OFF (disabled) on the "PFP"

menu in the startup menu.

(Refer to [6-3 Startup Menu].)

4-7

Last Setting Memory

This unit has a built-in last setting memory function that starts it up with the last setting state.

The unit memorizes the current settings after approx. two seconds after ending operations like

[OUTPUT ON/OFF] switch and voltage/current setting dial on on the front panel, etc.

When the unit is restarted in this state, the memorized settings just before the [POWER ON/OFF]

switch was turned OFF will be applied. However, the output state depends on the setting of the power

failure protection function.

Note that the settings cannot be memorized if the [POWER ON/OFF] switch is turned off within 2

seconds after setting.

Turn the current setting dial to select
"on" and "oFF" of the power failure
protection function.

VOLTAGE

CURRENT

Current setting dial

LOCK

OCP

SET

OVP/

OUTPUT

REMOTE

Содержание R4G Series





























































Результаты поиска

Содержание R4G Series

Отзывы:

Бренды по названию

Популярные бренды

Matsusada R4G Series, Инструкция по эксплуатации

Результаты поиска

Содержание R4G Series

Отзывы:

Бренды по названию

Популярные бренды