Masimo Root Скачать руководство пользователя страница 87

Страница: 87 / 152

www.masimo.com

Masimo

Chapter 5: NIBP Measurement

Root provides noninvasive blood pressure readings through an oscillometric method.
An oscillometric method of blood pressure measurement is a noninvasive method that

monitors the amplitude of cuff pressure changes during cuff deflation to determine arterial

blood pressure. The NIBP module is designed for use on adult, pediatric, and neonatal

patients.

Patient Measurement Mode

Below is a table that provides a method for selecting the appropriate NIBP patient category.

To change patient category see

Profiles

on page 53.

Weight

Patient Category Maximum Pressure

Greater than 75lbs (34kg)

Adult

280 mmHg

Between 15.4-75lbs (7-34kg) Pediatric

280 mmHg

Less than 15.4lbs (7kg)

Neonatal

140 mmHg

Cuff Selection and Placement

Root uses a quick connect hose with a blood pressure cuff to measure NIBP. Based on the Cuff

Type that is selected, use the following approved blood pressure cuff chart to choose sizes.

Accessory

Length

NIBP Patient Hose, Male Quick Connect 3 meters (9.8 feet)

NIBP Patient Hose, Female Bayonet

3 meters (9.8 feet)

Cuff Type

Size (color), Range - cm

Reusable Masimo Blood Pressure Cuff

Child (green), 12 - 19
Small Adult (turquoise), 17 - 25
Adult (navy blue), 23 - 33
Large Adult (burgundy), 31 - 40

Содержание Root

























































































































































Результаты поиска

Содержание Root

Отзывы:

Masimo Root, Руководство оператора, Страница: 87 / 152

Результаты поиска

Содержание Root

Отзывы: