Masimo Root Скачать руководство пользователя страница 51

Страница: 51 / 152

Root

Chapter 3: Operation

www.masimo.com

Masimo

Press

Enter

to access the password protected screen.

Note: The password will have to be entered every time this screen is accessed.

Option

Description

Factory

Default

Setting

Configurable Settings

All Mute

Enabled

Enable parameter Alarm Silence

menu option. See

Sounds

on page

56.

Off

On or Off

Lock Alarm

Volume

Sets the lowest alarm volume

level.

Off

3, 4, or Off

Standby

Enabled

Enable's option for Standby Mode.

See

Standby Mode

on page 72.

Off

On or Off

Standby

Reminder Tone

Interval

Allows for time interval of 30 sec,

1 min, 2 min, 3 min, 5 min, 10 min,

or 15 min, as well as Off.

30 sec

30 sec, 1 min, 2 min, 3

min, 5 min, 10 min, 15

min, Off

Save as Adult

Saves current profile parameter as

the Adult Profile.

N/A

Press

Save

to load.

Save as

Pediatric

Saves current profile parameter as

the Pediatric Profile.

N/A

Press

Save

to load.

Save as Neo

Saves current profile parameter as

the Neonatal Profile.

N/A

Press

Save

to load.

Factory Defaults Options are restored to factory

values.

N/A

Press

Restore

Содержание Root

























































































































































Результаты поиска

Содержание Root

Отзывы:

Masimo Root, Руководство оператора, Страница: 51 / 152

Результаты поиска

Содержание Root

Отзывы: