Masimo Root Скачать руководство пользователя страница 31

Страница: 31 / 152

www.masimo.com

Masimo

Chapter 3: Operation

The information in this chapter assumes that Root is set up and ready for use. This chapter

provides necessary information for proper operation of the device. Do not operate Root

without completely reading and understanding these instructions.

About the Status Bar

At the top of the Main Screen is the Status Bar with interactive icons. Each icon provides a

shortcut to a menu item or an action on Root. An example is shown below.

Ref. Feature

Description

Alarm Silence

Displays alarm status and temporarily mutes all audible alarms for

Root, Radical-7, Radius-7, and MOC-9 modules.
See

Alarm Silence

on page 70.

Audio Pause

Displays Audio Pause status and temporarily silences an alarm event.
See

Audio Pause

on page 71.

Standby Mode

Allows for patient monitoring to be temporarily suspended. Available

when using Root with Radius-7.
See

Standby Mode

on page 72.

Profiles

Provides access to the

Profiles

screen. The example shown illustrates

that Profiles is currently set to

Adult

for an adult patient.

See

Profiles

on page 53.

Bluetooth

Provides access to the

Bluetooth

screen. If this icon is visible, then

Bluetooth connectivity has been enabled.
See

Bluetooth

on page 46.

Wi-Fi

Provides access to the

Wi-Fi

screen. If this icon is visible, then Wi-Fi

connectivity has been enabled. The icon itself also indicates the

strength of the wireless signal.
See

Wi-Fi

on page 45.

Содержание Root

























































































































































Результаты поиска

Содержание Root

Отзывы:

Masimo Root, Руководство оператора, Страница: 31 / 152

Результаты поиска

Содержание Root

Отзывы: