M&R Challenger 2 Скачать руководство пользователя

Страница: 68 / 106

V.033114

M&R Companies 1N 372 Main St. Glen Ellyn, IL 60137 USA

Tel: +630-858-6101 Fax: +630-858-6134

www.mrprint.com

| store.mrprint.com

Frequency

Maintenance

Every
Three

Months

(Cont.)

Replace Air Filter Element and Reservoir Seal

Items required:

1 - Filter Element (M&R Part No. 2019114-A)
1 - Bowl Seal (M&R Part No. 2020091-1)
1 - 10 wt. Non-Detergent Oil (M&R Part No. 7017000)

1. Press and hold the orange button on the bottom of the filter

to bleed off any residual air which may remain in the system.

2. Remove the Moisture Trap (1) by pushing up and turning 1/8

of a turn counterclockwise. Pull the Reservoirs straight down
and away from the Filter/Regulator Assembly.

3. Remove Bowl Seal (5) from Reservoir and replace with new

Seal. Lightly lubricate the outside surface of the new seal
with 10 wt. Non-Detergent Oil.

4. Remove the Baffle (3) by turning to the left

(counterclockwise).

5. Install new Filter Element (4) and replace Baffle (3). Replace

Reservoir (1). Firmly push Reservoir up into the
Filter/Regulator Assembly and turn 1/8 turn to lock into
place.

Note: The level sight glass should be facing towards the front of the

assembly.

WARNING:

To prevent possible injury to personnel and/or damage to the equipment, lock out and tag the

electrical service and compressed air supply to the equipment.

Every Six

Months

Check Print Carriage Drive Belt Tension

Items required:

– 3/8” Hex Wrench

Note: Manually move the Print Carriage all the way towards the front of

the print station.

1. Check drive belt for proper tension. The belt should be

straight and taught.

If adjustment is needed, use a 3/8” Hex Wrench to loosen
the three socket cap screws (1) 2 full turns.

3. To increase drive belt tension, manually move the Print

Carriage Drive Assembly towards the rear of the print station

Содержание Challenger 2











































































































Результаты поиска

Содержание Challenger 2

Отзывы:

Похожие инструкции для Challenger 2

Бренды по названию

Популярные бренды

M&R Challenger 2, Руководство пользователя

Результаты поиска

Содержание Challenger 2

Отзывы:

Похожие инструкции для Challenger 2

Бренды по названию

Популярные бренды