Mami Mini TRACER, Руководство пользователя

Страница: 13 / 19

-11 -
S.P.I. (SECTIONAL PERIMETER INTRUSION ) OPTION REGISTERS PROGRAMMING (CONT.)
0
0
0
0
#
#
#
#
3
3
3
3
A
B
C
D
0
0
0
0
1
1
1
1
0
0
0
0
LEVEL "A" PRESET
LEVEL "B" PRESET
LEVEL "C" PRESET
LEVEL "D" PRESET
1 2 3 4 5 6
ARM
WARN
PER
An extra 6 perimeter beams may be connected to the new MINI-TRACER-Combo.( See SPI installation instructions)
The unit will monitor these perimeter beams and indicate which beam was triggered. The activation of the beams
will either sound locally or
will report the activation to the control room using exclusively zone 6.
The perimeter SECTORS are set up, tested and activated by following this procedure:
1- Connect , align and program each beam number
2- Manually or automatically define the number of sectors / beams installed as follows:
2
3
4
5
6
1
4 1 2 #
3 4
#
5 6 #
1 2
#
4
Each segment may be programmed to have different response times (on interruption of the Infrared beam).
These times may vary from 0,3 Seconds to 20 Seconds. Use the table to select the response (interruption time before alarm)
This is done using the USER 1 code.
USER1 CODE
SET SENSITIVITY LEVELS FOR EACH
SECTOR OF THE PERIMETER ALARM
1 # 9 1 1 1
{
? ?
#
Device No. Level of
response
1=0.3 Sec 5= 2 Sec
2=0.5 Sec 6= 5 Sec
3=0.8 Sec 7=10 Sec
4=1.2 Sec 8=20 Sec
1 # 0 1 1 1 1 3 #
ARM
WARN
PER
To arm individual segment of the perimeters enter:
“O” Indicates Perimeter
detection active
6
To test the perimeter connections do the following:
1- Enable/ activate all (6 in this case) available beams installed with:
0 # 2 6 0 1 0
Four preset perimeter selections may be pre-programmed to coincide with the arm/warn levels A,B,C & D.
(
This is done as shown below)
If option 6 of register 01 (page8 ) is set, a selection will be active when the corresponding arm/warn level is selected
( e.g. You can have zones 1&2 ( level “A”) on armed and perimeter sectors 1,2 &3 on warning
0 # 2
5
0
1
0
DEFINE INSTALLED SECTORS
12
#
3 4 5 6
1 #
0
1 1 1
2- Enable testing mode as follows ( in this mode no audible devices
are activated and the faulty/ non aligned beams will be displayed
0 # 2 7 0 1 0
3- Exit test mode by entering:
1 2 3 4 5 6
Or
0 #
2
3 0 1 0
AUTO ASSESS SECTORS
Wait for the display to show the sectors found then enter to store the result or any other key to exit.
. . .
12 3 4 5 6
#
Or
1 1 1 1
#
OFF = USE INDIVIDUAL OUTPUTS
OFF = LIGHT RELAY FOR 3 MINUTES
OFF = ANY 3 BREAKS
ON = LIGHT RELAY FOR 20 MINUTES
ON = IF THREE BREAKS ( SAME 3 BEFORE ALARM)
OFF = MASTER’S OUTPUT GOES HIGH (1 - 6)
ON = MASTER’S OUTPUT GOES LOW (1 - 6)
0 # 2
4
0
1
0
OPTIONS (SPI MODE) REGISTER NO.9
1
2
3
4
5
6
7
8
F
ACT
OR
Y
DEF
AUL
T
New!!
ON = USE COMMON OUTPUT (1) ON MASTER
1 2 3 4 5 6
{
INSTALLER CODE
THE INSTALLER MAY FURTHERMORE PROGRAM THE FOLLOWING OPTIONS
SPARE
ON = SYSTEM RESETS EVERY 3 HOURS
SPARE
SPARE
BEAMS
BEAMS
+ + +
- - -
NO SW
LIT
BUZ
8 7 6 5 4 3 2 1 -
TX RX
- +
A
B
SDA
SCK
LEARN
8 7 6 5 4 3 2 1
LED’S
TRANSMITTER
BEAMS
BEAMS
+ + +
- - -
NO SW
LIT
BUZ
8 7 6 5 4 3 2 1 -
TX RX
- +
A
B
SDA
SCK
LEARN
8 7 6 5 4 3 2 1
LED’S
TRANSMITTER
ARMING INDIVIDUAL
PERIMETER SECTIONAL BEAMS
OFF = NO AUTO-RESETS
e.g. Only beam 1, 2, 3, 4, 5 and 6 are installed.
Each segment may be programmed to activate either on a single or multiple break(3). See SPI instructions for this option
SPARE
SPARE
SPARE
M000037