Mami Mini TRACER, Руководство пользователя

Страница: 14 / 19

NOTE: THIS OPERATION WILL ERASE
BOTH THE MEMORY IN THE KEY BOARD
AND THE CONTROL UNIT AND RESTORE
THE FACTORY-DEFAULT VALUES .
IT COMBINES THE ABOVE 2 COMMANDS
NOTE: THIS OPERATION WILL ERASE
ALL PRESENT OPTIONS AND RESTORE
THE FACTORY-DEFAULT VALUES INCLUDING
ZONE, OPTIONS, WIRELESS CODES ETC ! ! !
(ALL SETTINGS SHOWN ON PAGES 7, 8, 9 & 10)
0
4
0
1
0
#
#
CHANGE KEYPAD ID
HOLD
TILL BEEP
POLLING
SP
ARE
SP
ARE
SP
ARE
SP
ARE
SP
ARE
SP
ARE
SP
ARE
0 # 1 0 1 0 ENABLE KEYPADS
HOLD
TILL BEEP
NOTE: THIS REGISTER ENABLES THE COMMUNICATION
BETWEEN THE SUPER TRACER AND
KEYPADS.
NOTE: THE KEYPAD ID IS THE SUBSCRIBER I.D.
AS ON PAGE 9 REGISTER “1C”.
1 2 3
4
5 6 7
8
1 2 3 4
0 # D 0 1 0
HOLD
TILL BEEP
SET INDIVIDUAL key pad I.D. NUMBER
MORE THAN 1 SELECTION IS ALLOWED.
e.g. If 1 & 2 were selected, the unit
will respond to all commands addressed to
key pads 1 & 2.
THE CURRENT CONTENT OF THE SELECTED REGISTER
WILL BE DISPLAYED.USE BUTTONS 0 TO 8 TO
CHANGE THE CORRESPONDING BIT TO OBTAIN
THE DESIRED SELECTION. PRESS " # " TO EXIT.
ENTER THE INSTALLER CODE FOLLOWED BY A LONG "#" KEY AND THE
NUMBER OF THE REGISTER YOU WANT TO MODIFY.
NOTE : THE " # " MUST BE HELD DOWN UNTIL YOU HEAR A LONG BEEP.
THE SUPER TRACER CAN ACCEPT UP TO 4 KEYPADS.
FOR SPECIAL APPLICATIONS EACH KEYPAD CAN
BE PROGRAMMED TO HAVE ITS OWN I.D. CODE.
KEYPADS WITH THE SAME I.D. WILL OPERATE SIMILARLY.
REGISTER NAME INSTALLER CODE REG. NO.
= ON
= UNUSED
= OFF
NOTE:
0 #
9
0
1
0
ERASE KEYBOARD MEMORY
HOLD
TILL BEEP
NOTE: THIS OPERATION WILL ERASE
ALL PRESENT VALUES AND RESTORE
THE FACTORY-DEFAULT VALUES INCLUDING
KEYBOARD SETTINGS AND USER CODES ! ! !
( ALL SETTINGS SHOWN ON PAGE 12)
0
C 0 ? ? ? ?
0 1 0
#
#
NEW CODE (4 DIGITS)
CHANGE CODE OF USER 1 to 10(A)
CHANGE INSTALLER CODE
0 0
1
0
#
HOLD
TILL BEEP
HOLD
TILL BEEP
AFTER THE NEW CODE ENTRY,
THE CODE WILL BE DISPLAYED
ONE DIGIT AT THE TIME.
ENTER " # " TO ACCEPT THE CODE
AFTER IT HAS BEEN DISPLAYED.
ANY OTHER KEY WILL REQUIRE THE
NEW CODE TO BE RE-ENTERED.
{
NEW CODE (4 DIGITS)
{
C X ?
#
? ? ?
USER NO 1,2,3,4,5,6,7,8,9,A
(MULTI-USER MODE - 2,3,4,5 ONLY)
Note: IN MULTIUSER MODE USER 5 REPLACES USER 1
(no USER 1 rights are available in this mode
-12-
MAINS
BCKUP
LO-BA
T
SP
ARE
TRIGG
DELA
Y
SP
ARE
AUX.
0 # 3 0 1 0
ENABLE LOCAL BLEEPER FUNCTIONS
HOLD
TILL BEEP
NOTE: THIS REGISTER DEFINES WHICH
CONDITIONS WILL ACTIVATE THE LOCAL BLEEPER.
1 2 3
4
5 6 7
8
MAINS: Mains Failure
BCKUP : System battery low
LO-BAT: Sensor battery low.
TRIGG: Alarm triggered.
DELAY : Entry Exit Delay
AUX: Key Beeps ON/OFF.
? ? ? ?
NEW CODE (4 DIGITS)
PROGRAMMING (CONT.) KEYPAD OPTION REGISTERS
1 2 3 4 5 6
ARM
WARN
PER
0 # 0 9 0 1 0
ERASE MEMORY
IN CONTOL UNIT
0 # 2 9 0 1 0
ERASE BOTH CONTROL-UNIT
AND KEY-BOARD MEMORIES
After this command the unit will
reset to load the default values!
After this command the unit will
reset to load the default values!
After this command the unit will
reset to load the default values!
!
!
!
!
!
!
DEFAULTING THE SYSTEM (ERASING MEMORIES)
M000037