Malvern MPT-2 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 85

Malvern MPT-2 Скачать руководство пользователя страница 75

Appendices

Appendix A

MPT-2 & Degasser

Page A-5

Electrical Power Requirements

The mains power supply must be clean and filtered. If necessary, fit an un-inter-
ruptible power supply (UPS) to remove any spikes or noise. The power require-
ment for the Vacuum degasser is indicated below.

Caution!

Use the correct power lead for the territory.

A set of four interchangeable adaptor plugs are is included to allow the AC adapter
to be plugged into the standard electrical wall sockets in North America, Japan, the
U.K., most countries in continental Europe, and Australia.

If it is necessary to replace the AC Adapter - Contact Malvern instruments about
replacement.

Note

Refer to the

Health and Safety

section on the main

Zetasizer Nano

User manual

for more information.

Power requirement

100 to 240VAC / 47 to 63Hz

MAN0318-4.0 - MPT-2 Autotitrator-Degasser.book Page 5 Tuesday, September 4, 2012 12:15 PM

«
...
73
74
75
76
77
...
»

Содержание MPT-2






















































































Отзывы:

Нет отзывов