Malvern MPT-2 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 85

Malvern MPT-2 Скачать руководство пользователя страница 22

Chapter 1

Introduction and hardware

Page 1-16

MAN 0318

Power Connector

Caution!

Only use the AC power adaptor as supplied from Malvern Instruments.

Connect the output plug from the AC power adaptor to this connector.

See

Specifications

chapter for further power requirement information.

Power Switch

The On/Off power switch turns the Vacuum Degasser On,

Exhaust Port

Any gas pumped out of the vacuum chamber exits the unit through the exhaust
port.

Validation Connector

Depending on the model, there may be a 2-pin receptacle labelled "Validation"
located next to the power switch. This receptacle and its associated screw-lock plug
allow a validation signal from the Vacuum Degasser's control circuit to be sent to a
computer or data system. This validation output indicates vacuum level (see

Spec-

ifications

section for details).

O

= Off

I

= On.

MAN0318-4.0 - MPT-2 Autotitrator-Degasser.book Page 16 Tuesday, September 4, 2012 12:15 PM

«
...
20
21
22
23
24
...
»

Содержание MPT-2






















































































Отзывы:

Нет отзывов