Malvern MPT-2 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 85

Malvern MPT-2 Скачать руководство пользователя страница 21

Introduction and hardware

Chapter 1

MPT-2 & Degasser

Page 1-15

Front Panel Indicators

Three LEDs are located on the front of the instrument above the titrant inlets and
outlets; these indicate the following.

Rear Panel Connections and Controls

ill 8734

Power (Green)

Indicates when power is applied to the Vacuum Degasser -
cable is plugged in and Power switch turned ON.

Status (Yellow)

Indicates when vacuum level is outside the acceptable oper-
ating range. This LED will light at initial power-up and remain
on during pump-down. It will turn off after a few minutes
when the vacuum level goes below 100 mm of Hg absolute.

If an error condition occurs, this LED will flash in one of two
modes:

Flashing on and off in even 1-second intervals: pump was
not able to reach vacuum set point, indicating a possible
leak in the system.

Flashing on for 1 second and off for 2 seconds indicates a
vacuum signal error.

Vacuum (Green)

Indicates when vacuum level is within the acceptable operat-
ing range. The LED will light up after the initial pump-down,
and remain on as long as the Vacuum Degasser is powered
up and the vacuum level is below 100 mm of Hg absolute.

Power
Switch

Rear of
Vacuum
Degasser

POWER
15 - 24V

DC

0.85A MAX

EXHAUST

+

VALIDATION

+

MAN0318-4.0 - MPT-2 Autotitrator-Degasser.book Page 15 Tuesday, September 4, 2012 12:15 PM

«
...
19
20
21
22
23
...
»

Содержание MPT-2






















































































Отзывы:

Нет отзывов