madur electronics maMoS 100 Скачать руководство пользователя страница 49

Страница: 49 / 96

www.madur.com

Manual

maMoS

100/200/300/400

11. To check whether the programming process has been successful the user

should:

−

switch the monitor off

−

remove the jumper

−

switch the monitor on and confirm whether the firmware version is correct

(appears on the display

several seconds after the device has been

switched on

)

. If the firmware version is correct the monitor can be switched

off and the casing of the device should be closed.

Picture 52.

Information of the completion of the updating process.

5.6. Flow velocity measurement

MaMoS

analyser can optionally measure gas flow velocity (for example in chim-

neys). If this option is available then the analyser is equipped with the pressure measure -

ment inlet and outlet. They are installed at the bottom part of the housing next to fresh air

inlet and gas outlet.

The measurement of the flow velocity is made via measurement of total and static

pressure using Pitot tube. To perform the measurement correctly connect the Pitot tube as

follows:

The outlet of the static pressure connect to the inlet signed with

symbol

The inlet of the total pressure connect to the inlet signed with

symbol

Содержание maMoS 100

































































































Результаты поиска

Содержание maMoS 100

Отзывы:

madur electronics maMoS 100, Руководство пользователя, Страница: 49 / 96

Результаты поиска

Содержание maMoS 100

Отзывы: