madur electronics maMoS 100 Скачать руководство пользователя страница 93

Страница: 93 / 96

www.madur.com

Manual

maMoS

100/200/300/400

7.3.11.1. IR sensor calibration

After the sensor which is to be calibrated has been chosen from the „1-point calib-

ration” menu, the window shown below will appear.

Picture 104.

The window containing the IR sensor readings.

To execute calibration:

1. Apply a neutral (for the specified sensor) gas to the device and wait for the

values in fields "

Ch1"

, "

Norm."

and "

Ch2"

to stabilize. Press

“Hold readouts”

button

Picture 105.

The readings if the zeroing gas is supplied.

2. Enter the concentration of the neutral gas into

“Zeroing gas”

field, and then

press

“Make zeroing”

button.

3. After zeroing, apply the reference gas and enter it's concentration into

“Calib-

ration Gas"

field. Then, press

“Read"

and wait for the values in fields "

Ch1”

Norm."

and "

Ch2"

to stabilize.

Содержание maMoS 100

































































































Результаты поиска

Содержание maMoS 100

Отзывы:

madur electronics maMoS 100, Руководство пользователя, Страница: 93 / 96

Результаты поиска

Содержание maMoS 100

Отзывы: