madur electronics maMoS 100 Скачать руководство пользователя страница 20

Страница: 20 / 96

www.madur.com

Manual

maMoS

100/200/300/400

RS485 Switch

to communicate with several

maMoS

devices,

temperature sensors: thermocouple (temperature range up to 1000°C) or Pt

sensor (temperature range up to 100°C),

atmospheric pressure sensor,

differential pressure sensor, range: -5 ÷ +20hPa or -20 ÷ 20hPa,

differential pressure sensor with gas channel flow control and dryer's filter

contamination level control,

Pitot's tube - used for indirect measurements of gas flow velocity with the

help of the differential pressure sensor.

4. MONITOR INSTALLATION

Mounting the monitor upright on a wall will assure correct function. The device

should be installed in a place not exposed to weather conditions (rain, snow, sun expos-

ure, temperatures below 0°C and above 40°C). It is advisable to avoid high dust concen-

tration in the air.

To attach the monitor to the wall the user should make four holes in the wall (dia-

meter

∅

= 10mm). The placement of the mounting holes is presented in the below draw-

ing.

Picture 18.

Mounting holes placement

Picture 19.

Mounting holes placement

The monitor should be attached to the wall with screws (the set of needed screws

has been enclosed with the monitor – see Picture 3.).

Содержание maMoS 100

































































































Результаты поиска

Содержание maMoS 100

Отзывы:

madur electronics maMoS 100, Руководство пользователя, Страница: 20 / 96

Результаты поиска

Содержание maMoS 100

Отзывы: