LG-Ericsson iPECS ES-2024G Скачать руководство пользователя страница 9

Страница: 9 / 60

OMPLIANCES

– 9 –

ES-2024G/2024GP

◆

Waste reduction and safe disposal of all harmful un-recyclable by-

products.

◆

Recycling of all reusable waste content.

◆

Design of products to maximize recyclables at the end of the product’s

life span.

◆

Continual monitoring of safety standards.

RODUCT

IFE

PAN

This product is manufactured in such a way as to allow for the recovery and

disposal of all included electrical components once the product has reached

the end of its life.

ANUFACTURING

ATERIALS

There are no hazardous nor ozone-depleting materials in this product.

OCUMENTATION

All printed documentation for this product uses biodegradable paper that

originates from sustained and managed forests. The inks used in the

printing process are non-toxic.

Содержание iPECS ES-2024G





























































Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды

LG-Ericsson iPECS ES-2024G, Руководство по установке

Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды