LG-Ericsson iPECS ES-2024G Скачать руководство пользователя страница 16

Страница: 16 / 60

– 16 –

ES-2024G/2024GP

NTRODUCTION

VERVIEW

The ES-2024G and ES-2024GP are Gigabit Ethernet Layer 2 switches with

24 10/100/1000-BASE-T ports, and four Small Form Factor Pluggable (SFP)

transceiver slots that operate in combination with ports 21~24 (see

Figure 1

). The ES-2024GP also provides PoE power to connected devices.

The switches also include an SNMP-based management agent, which

provides in-band access for managing the switch.

Both switches provide a broad range of powerful features for Layer 2

switching, delivering reliability and consistent performance for your

network traffic. They bring order to poorly performing networks by

segregating them into separate broadcast domains with IEEE 802.1Q

compliant VLANs, and empowers multimedia applications with multicast

switching and CoS services.

Figure 1: ES-2024G and ES-2024GP Front Panels

Figure 2: Rear Panel

ES-2024G

Port Status Indicators

System Indicators

10/100/1000 Mbps RJ-45 Ports

1000BASE-T/SFP Ports

ES-2024GP

Port Status Indicators

System Indicators

10/100/1000 Mbps RJ-45 PoE Ports

1000BASE-T/SFP Ports

Mode Button

AC 100-240V, 50-60Hz, 3A

Reset

Reset Button

Grounding Point

Power Inlet

Содержание iPECS ES-2024G





























































Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды

LG-Ericsson iPECS ES-2024G, Руководство по установке

Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды