LG-Ericsson iPECS ES-2024G Скачать руководство пользователя страница 53

Страница: 53 / 60

– 53 –

ES-2024G/2024GP

LOSSARY

10BASE-T

IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3,

4, or 5 UTP cable.

100BASE-FX

IEEE 802.3 specification for 100 Mbps Ethernet over two strands of 50/125,

62.5/125 micron, or 9/125 micron core fiber cable.

100BASE-TX

IEEE 802.3u specification for 100 Mbps Ethernet over two pairs of Category

5 UTP cable.

1000BASE-LX

IEEE 802.3z specification for Gigabit Ethernet over two strands of 50/125,

62.5/125 or 9/125 micron core fiber cable.

1000BASE-LH

Specification for long-haul Gigabit Ethernet over two strands of 9/125

micron core fiber cable.

1000BASE-SX

IEEE 802.3z specification for Gigabit Ethernet over two strands of 50/125

or 62.5/125 micron core fiber cable.

1000BASE-T

IEEE 802.3ab specification for Gigabit Ethernet over 100-ohm Category 5,

5e or 6 twisted-pair cable (using all four wire pairs).

UTO

-N

EGOTIATION

Signalling method allowing each node to select its optimum operational

mode (e.g., speed and duplex mode) based on the capabilities of the node

to which it is connected.

ANDWIDTH

The difference between the highest and lowest frequencies available for

network signals. Also synonymous with wire speed, the actual speed of the

data transmission along the cable.

OLLISION

OMAIN

Single CSMA/CD LAN segment.

CSMA/CD

CSMA/CD (Carrier Sense Multiple Access/Collision Detect) is the

communication method employed by Ethernet, Fast Ethernet, and Gigabit

Ethernet.

Содержание iPECS ES-2024G





























































Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды

LG-Ericsson iPECS ES-2024G, Руководство по установке

Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды