LG-Ericsson iPECS ES-2024G Скачать руководство пользователя страница 5

Страница: 5 / 60

OMPLIANCES

– 5 –

ES-2024G/2024GP

AFETY

OMPLIANCE

SAFETY INSTRUCTION

This product complies with and conforms to the following international

Product Safety standards as applicable:

◆

Safety of Information Technology Equipment, IEC(EN) 60950-1,

including all relevant national deviations as listed in Compliance with

IEC for Electrical Equipment (IECEE)

◆

Safety of Information Technology Equipment, CAN/CSA-C22.2 No.

60950-1/UL 60950-1

OWER

ORD

AFETY

Please read the following safety information carefully before installing the

switch:

WARNING: Installation and removal of the unit must be carried out by

qualified personnel only.

◆

The unit must be connected to an earthed (grounded) outlet to comply

with international safety standards.

◆

Do not connect the unit to an A.C. outlet (power supply) without an

earth (ground) connection.

◆

The appliance coupler (the connector to the unit and not the wall plug)

must have a configuration for mating with an EN 60320/IEC 320

appliance inlet.

◆

The socket outlet must be near to the unit and easily accessible. You

can only remove power from the unit by disconnecting the power cord

from the outlet.

◆

This unit operates under SELV (Safety Extra Low Voltage) conditions

according to IEC 60950. The conditions are only maintained if the

equipment to which it is connected also operates under SELV

conditions.

France and Peru only

This unit cannot be powered from IT† supplies. If your supplies are of IT

type, this unit must be powered by 230 V (2P+T) via an isolation

transformer ratio 1:1, with the secondary connection point labelled

Neutral, connected directly to earth (ground).

† Impédance à la terre

Important!

Before making connections, make sure you have the correct

cord set. Check it (read the label on the cable) against the following:

Содержание iPECS ES-2024G





























































Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды

LG-Ericsson iPECS ES-2024G, Руководство по установке

Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды