LG-Ericsson iPECS ES-2024G Скачать руководство пользователя страница 8

Страница: 8 / 60

OMPLIANCES

– 8 –

ES-2024G/2024GP

◆

Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich

sein. Die Stromversorgung des Geräts kann nur durch Herausziehen

des Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.

◆

Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen

(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen

sind nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte

unter SELV-Bedingungen betrieben werden.

ARNINGS

AND

AUTIONARY

ESSAGES

ARNING

This product does not contain any serviceable user parts.

ARNING

Installation and removal of the unit must be carried out by

qualified personnel only.

ARNING

When connecting this device to a power outlet, connect the field

ground lead on the tri-pole power plug to a valid earth ground line to

prevent electrical hazards.

ARNING

This switch uses lasers to transmit signals over fiber optic cable.

The lasers are compliant with the requirements of a Class 1 Laser Product

and are inherently eye safe in normal operation. However, you should

never look directly at a transmit port when it is powered on.

AUTION

Wear an anti-static wrist strap or take other suitable measures to

prevent electrostatic discharge when handling this equipment.

AUTION

Do not plug a phone jack connector in the RJ-45 port. This may

damage this device.

AUTION

Use only twisted-pair cables with RJ-45 connectors that conform

to FCC standards.

NVIRONMENTAL

TATEMENTS

The manufacturer of this product endeavours to sustain an

environmentally-friendly policy throughout the entire production process.

This is achieved though the following means:

◆

Adherence to national legislation and regulations on environmental

production standards.

◆

Conservation of operational resources.

Stromkabel

. Dies muss von dem Land, in dem es benutzt wird geprüft werden:

Schweiz

Dieser Stromstecker muß die SEV/ASE

1011Bestimmungen einhalten.

Europe

Das Netzkabel muss mit IEC 60227 (IEC 60227

entsprechen Bezeichnung 52)
Der Netzstecker muß die Norm CEE 7/7 erfüllen

(”SCHUKO”).

Содержание iPECS ES-2024G





























































Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды

LG-Ericsson iPECS ES-2024G, Руководство по установке

Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды