LG-Ericsson iPECS ES-2024G Скачать руководство пользователя страница 18

Страница: 18 / 60

HAPTER

| Introduction

Description of Hardware

– 18 –

ES-2024G/2024GP

support auto-negotiation, the communication mode of that port can be

configured manually.

Each port also supports IEEE 802.3x auto-negotiation of flow control, so

the switch can automatically prevent port buffers from becoming

saturated.

SFP T

RANSCEIVER

LOTS

The Small Form Factor Pluggable (SFP) transceiver slots on the ES-2024G

and ES-2024GP are shared with four of the RJ-45 ports (ports 21~24). In

its default configuration, if an SFP transceiver (purchased separately) is

installed in a slot and has a valid link on its port, the associated RJ-45 port

is disabled and cannot be used. The switch can also be configured to force

the use of an RJ-45 port or SFP slot, as required.

The following table shows a list of transceiver types which have been

tested with the switches. For an updated list of vendors supplying these

transceivers, contact your local dealer. For information on the

recommended standards for fiber optic cabling, see

“Fiber Standards” on

page 49

ORT

AND

YSTEM

TATUS

LED

These switches include a display panel for key system and port indications

that simplify installation and network troubleshooting. The LEDs, which are

located on the front panel for easy viewing, are shown below and described

in the following tables.

Table 1: Supported SFP Transceivers

Media Standard

Fiber Diameter

(microns)

Wavelength

(nm)

Maximum Distance

Maximum distance may vary for different SFP vendors.

1000BASE-SX

50/125

850

700 m

62.5/125

850

400 m

1000BASE-LX

50/125

1300

550 m

62.5/125

1300

550 m

9/125

1300

10 km

1000BASE-LH

9/125

1310

35 km

1550

80 km

100BASE-FX

50/125 or 62.5/125

1300

2 km

9/125

1300

20 km

1000BASE-T

100 m

Содержание iPECS ES-2024G





























































Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды

LG-Ericsson iPECS ES-2024G, Руководство по установке

Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды