LG-Ericsson iPECS ES-2024G Скачать руководство пользователя страница 49

Страница: 49 / 60

PPENDIX

| Cables and Pinouts

Fiber Standards

– 49 –

ES-2024G/2024GP

ABLE

ESTING

FOR

XISTING

ATEGORY

5 C

ABLE

Installed Category 5 cabling must pass tests for Attenuation, Near-End

Crosstalk (NEXT), and Far-End Crosstalk (FEXT). This cable testing

information is specified in the ANSI/TIA/EIA-TSB-67 standard. Additionally,

cables must also pass test parameters for Return Loss and Equal-Level Far-

End Crosstalk (ELFEXT). These tests are specified in the ANSI/TIA/EIA-

TSB-95 Bulletin, “The Additional Transmission Performance Guidelines for

100 Ohm 4-Pair Category 5 Cabling.”

Note that when testing your cable installation, be sure to include all patch

cables between switches and end devices.

DJUSTING

XISTING

ATEGORY

5 C

ABLING

1000BASE-T

If your existing Category 5 installation does not meet one of the test

parameters for 1000BASE-T, there are basically three measures that can be

applied to try and correct the problem:

Replace any Category 5 patch cables with high-performance Category
5e or Category 6 cables.

Reduce the number of connectors used in the link.

Reconnect some of the connectors in the link.

IBER

TANDARDS

Table 14: Fiber Standards

ITU-T Standard

Description

Application

G.651

Multimode Fiber
50/125-micron core

Short-reach connections in the

1300-nm or 850-nm band.

G.652

Non-Dispersion-Shifted Fiber
Single-mode, 9/125-micron core

Longer spans and extended reach.

Optimized for operation in the 1310-

nm band. but can also be used in the

1550-nm band.

G.652.C

Low Water Peak Non-Dispersion-

Shifted Fiber
Single-mode, 9/125-micron core

Longer spans and extended reach.

Optimized for wavelength-division

multiplexing (WDM) transmission

across wavelengths from 1285 to

1625 nm. The zero dispersion

wavelength is in the 1310-nm

region.

G.653

Dispersion-Shifted Fiber
Single-mode, 9/125-micron core

Longer spans and extended reach.

Optimized for operation in the region

from 1500 to 1600-nm.

G.654

1550-nm Loss-Minimized Fiber
Single-mode, 9/125-micron core

Extended long-haul applications.

Optimized for high-power

transmission in the 1500 to 1600-nm

region, with low loss in the 1550-nm

band.

G.655

Non-Zero Dispersion-Shifted Fiber
Single-mode, 9/125-micron core

Extended long-haul applications.

Optimized for high-power dense

wavelength-division multiplexing

(DWDM) operation in the region from

1500 to 1600-nm.

Содержание iPECS ES-2024G





























































Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды

LG-Ericsson iPECS ES-2024G, Руководство по установке

Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды