LG-Ericsson iPECS ES-2024G Скачать руководство пользователя страница 27

Страница: 27 / 60

HAPTER

| Network Planning

Application Examples

– 27 –

ES-2024G/2024GP

AKING

VLAN

ONNECTIONS

These switches support VLANs which can be used to organize any group of

network nodes into separate broadcast domains. VLANs confine broadcast

traffic to the originating group, and can eliminate broadcast storms in large

networks. This provides a more secure and cleaner network environment.

VLANs can be based on untagged port groups, or traffic can be explicitly

tagged to identify the VLAN group to which it belongs. Untagged VLANs can

be used for small networks attached to a single switch. However, tagged

VLANs should be used for larger networks, and all the VLANs assigned to

the inter-switch links.

These switches also support multiple spanning trees which allow VLAN

groups to maintain a more stable path between all VLAN members. This

can reduce the overall amount of protocol traffic crossing the network, and

provide a shorter reconfiguration time if any link in the spanning tree fails.

At Layer 3, VLANs are used to create an IP interface, where one or more

ports are assigned to the same IP segment. Traffic is automatically routed

between different IP segments on the same switch, without any need to

configure routing protocols.

Figure 11: Making VLAN Connections

OTE

When connecting to a switch that does not support IEEE 802.1Q

VLAN tags, use untagged ports.

VLAN unaware

switch

Testing

R&D

Finance

Marketing

VLAN 3

Finance

R&D

Testing

Tagged Ports

Untagged Ports

Tagged Ports

VLAN unaware

switch

VLAN 1

VLAN 2

VLAN 3

VLAN 4

VLAN 2

VLAN 1

Содержание iPECS ES-2024G





























































Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды

LG-Ericsson iPECS ES-2024G, Руководство по установке

Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды