LG-Ericsson iPECS ES-2024G Скачать руководство пользователя страница 4

Страница: 4 / 60

OMPLIANCES

– 4 –

ES-2024G/2024GP

CE M

ARK

ECLARATION

ONFORMANCE

FOR

EMI

AND

AFETY

(EEC)

This information technology equipment complies with the requirements of

the Council Directive 2004/108/EC on the Approximation of the laws of the

Member States relating to Electromagnetic Compatibility and 2006/95/EC

for electrical equipment used within certain voltage limits and the

Amendment Directive 93/68/EEC. For the evaluation of the compliance

with these Directives, the following standards were applied:

The following declaration is for two models:

RFI Emission:

◆

Limit class A according to EN 55022:2006+A1:2007

◆

Limit class A for harmonic current emission

according to EN 61000-3-2/2006

◆

Limitation of voltage fluctuation and flicker in low-

voltage supply system according to EN 61000-3-3/

1995+A2:2005

Immunity:

◆

Product family standard according to EN

55024:1998+A2:2003

◆

Electrostatic Discharge according to IEC 61000-4-

2:1995+A: 1998+A2:2000 (Contact Discharge: ±4

kV, Air Discharge: ±8 kV)

◆

Radio-frequency electromagnetic field according to

IEC 61000-4-3:2006 (80 - 1000 MHz with 1 kHz AM

80% Modulation: 3 V/m)

◆

Electrical fast transient/burst according to IEC

61000-4-4:2004

(AC/DC power supply: ±1 kV, Data/Signal lines:

±0.5 kV)

◆

Surge immunity test according to IEC 61000-4-

5:2005

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2

kV)

◆

Immunity to conducted disturbances, Induced by

radio-frequency fields: IEC 61000-4-6:2006 (0.15 -

80 MHz with 1 kHz AM 80% Modulation: 3 V/m)

◆

Voltage dips, short interruptions and voltage

variations immunity test according to IEC 61000-4-

11:2004 (>95% Reduction @10 ms, 30% Reduction

@500 ms, >95% Reduction @5000 ms)

LVD:

◆

EN 60950-1:2006+A11:2009

Содержание iPECS ES-2024G





























































Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды

LG-Ericsson iPECS ES-2024G, Руководство по установке

Результаты поиска

Содержание iPECS ES-2024G

Отзывы:

Похожие инструкции для iPECS ES-2024G

Бренды по названию

Популярные бренды