Leuze electronic MSI-TRMB Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 47

Leuze electronic MSI-TRMB Скачать руководство пользователя страница 25

Electrical connection

Leuze electronic

MSI-TRMB

25

EDM configuration
Further information see chapter 4.7.

Table 7.3:

EDM configuration

ª

Trigger a reset (software reset via the start button if the device is in the error state, or by briefly switching

off the voltage supply at A1 / using reset button connected in series to the supply voltage at A1).

The new settings are accepted.
Connection examples

Figure 7.1: Safety monitoring device with one protective sensor with monitored start (restart interlock)

Function

Terminals

EDM selected

Monitored start: External device monitoring circuit (EDM) is connected to the start

button and terminal S35 in series relative to the starter button

Non-monitored start: External device monitoring circuit (EDM) is connected to the

start button and terminal S34 in series relative to the starter button

Automatic start: External device monitoring circuit (EDM) is connected to terminals

S33 and S34 in place of the bridge for automatic start

0V

Var. B

Var. A

+2

4

V

State

Er

ro

r

MSI-TRMB

active

Receiver

0V

+

2

4V

1 AOPD

St

a

rt

-K1

-K2

S11

-A3

A2

S22

S12

S36

S35

S31 14

24

S21

13

23

-K2

-K1

-K1

-K2

A1

A2

-K1

A1

A2

-K2

1

2

1

2

4

4

3

-A2

1

A1

0V

+ 24V

PE

L-

L+

+ 24V

0V

PE

L+

L-

3

1

Transmitter

-A1

+2

4

V

0V

«
...
23
24
25
26
27
...
»

Содержание MSI-TRMB
















































Отзывы:

Нет отзывов