Leuze electronic MSI-TRMB Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 47

Leuze electronic MSI-TRMB Скачать руководство пользователя страница 19

Mounting

Leuze electronic

MSI-TRMB

19

6

Mounting

The safety relay is intended for mounting on a DIN rail in the switch cabinet.

Prerequisites for mounting:

• Switch cabinet with appropriate degree of protection (at least IP54).
• Sufficient space on the DIN rail.
• Arrangement of the protective device acc. to ISO 13855 see chapter 6.1 "Arrangement of the protec

ª

Snap the safety relay onto the DIN rail.

The safety relay can be connected to the protective sensor.

6.1

Arrangement of the protective device

Optical protective devices can only perform their protective function if they are mounted with adequate

safety distance. When mounting, all delay times must be taken into account, e.g. the response times of

the protective sensor and control elements as well as the stopping time of the machine.

The following standards specify calculation formulas:

• ISO 13855, "The positioning of protective devices in respect of approach speeds of parts of the

human body": mounting situation and safety distances.

• IEC 61496-2, "Active optoelectronic protective devices": distance of the reflecting surfaces/deflecting

mirrors.

Table 6.1:

Beam heights and distances

6.1.1 Calculating the safety distance

General formula for calculating the safety distance S of an Optoelectronic Protective Device acc. to

ISO 13855:

S

[mm]

= Safety distance

K

[mm/s]

= 1600 mm/s (approach speed for access guarding)

T

[s]

= Total time of the delay

C

[mm]

= 850 mm (default value for arm length)

ª

Calculate safety distance S for access guarding using the formula acc. to ISO 13855:

WARNING

Improper mounting may result in serious injury!
The protective function of the safety relay is only ensured if appropriately and professionally mounted for

the respective, intended area of application.

ª

Only allow competent persons to install the safety relay.

ª

Observe the relevant standards, regulations and these instructions.

Number of beams/beam distance [mm]

Beam heights in accordance with ISO 13855 [mm]

2 / 500

400, 900

3 / 400

300, 700, 1100

4 / 300

300, 600, 900, 1200

S

K T C

+



=

«
...
17
18
19
20
21
...
»

Содержание MSI-TRMB
















































Отзывы:

Нет отзывов