manualshive.com logo in svg

Leuze electronic MSI-TRMB, Оригинальная инструкция по эксплуатации, Страница: 12 / 47

Поделиться
Скачать
Leuze electronic MSI-TRMB Скачать руководство пользователя страница 12

Device description

Leuze electronic

MSI-TRMB

12

3.3

Error display

Table 3.2:

Error display via LEDs

PWR

Green

Power on

PWR

Green, flashing

Supply voltage not correct (see chapter 14.1 "Gen

-

eral specifications")

Fault

Red

Internal or external fault (see chapter 3.3 "Error 

display")

LED

Color

Description

LED indicator

Errors and possible causes Remedial measures

Fault

IN1, IN2

OUT1, OUT2

On

Flashing

Off

Start button / bridge is (with 

automatic, non-monitored 

start) not connected to S21

Disconnect device from 

power supply, check for wir

-

ing faults, replace device if 

defective

Change of start condition 

during operation

On

Off

Flashing  

alternately

Output S11/S21 short-circuit 

to GND

Disconnect device from 

power supply, check wiring, 

replace device if defective or 

check connected ESPE

Output S11/S21 short-circuit 

to VCC

Incorrect input signals, incor

-

rect operating mode

Reaction time of ESPE is 

longer than 8.5 ms

Cross-circuit between S11 

and S21 or S12 and S22

Short-circuit of triggering ele

-

ments in the case of ESPE 

applications

On

Off

Flashing

Error during relay test – 

internal relay defective / 

fused together

Disconnect device from 

power supply, check con

-

nections at relay contacts, 

check max. output capability 

(see chapter 14.1 "General 

specifications"), replace 

device if defective

Содержание MSI-TRMB
















































Отзывы:

Нет отзывов