Leuze electronic MSI-TRMB Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 47

Leuze electronic MSI-TRMB Скачать руководство пользователя страница 14

Functions

Leuze electronic

MSI-TRMB

14

4

Functions

After the safety relay is switched on, the device performs a self test. During this test, the operating mode

in which the safety relay is to function is determined on the basis of the wiring. The basic wiring configu

-

rations of the individual operating modes are given below.

4.1

Operating mode 1 AOPD

Safety monitoring device with one or more protective sensors connected in series used for safeguarding

danger zones or points of operation on machines and systems.

AOPD = one or more protective sensors connected in series

Figure 4.1: Basic wiring for operating mode 1 AOPD (one protective sensor)

4.2

Operating mode 2 AOPD

Safety monitoring device with two protective sensors or two series connections consisting of multiple

protective sensors used for safeguarding danger zones or points of operation on machines and systems.

AOPD = one or more protective sensors connected in series

Figure 4.2: Basic wiring for operating mode 2 AOPDs (two protective sensors)

4.3

Operating mode ES

Safety sequential device for 2-channel E-Stop monitoring with NC contacts.

ES

= mechanical E-Stop switch (2-channel)

Figure 4.3: Basic wiring of operating mode ES (E-Stop)

If protective sensors are linked together in the way shown in the connection examples (see

figure 7.3 and see figure 7.4), the total delay time (0.5 ms to 8.5 ms) should be noted.

AOPD

S11

S12

S21

S22

S32

If protective sensors are linked together in the way shown in the connection examples (see

figure 7.7 and see figure 7.8), the total delay time (0.5 ms to 8.5 ms) should be noted.

AOPD

AOPD

S11

S12

S21

S22

S32

Automatic start is not approved for E-Stop applications.

ES

S11

S12

S21

S22

S32

ES

«
...
12
13
14
15
16
...
»

Содержание MSI-TRMB
















































Отзывы:

Нет отзывов