Leuze electronic MSI-TRMB Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 47

Leuze electronic MSI-TRMB Скачать руководство пользователя страница 15

Functions

Leuze electronic

MSI-TRMB

15

4.4

Operating mode SG

Safety sequential device for 2-channel safety door monitoring.

SG

= mechanical safety door switch (2-channel)

Figure 4.4: Basic wiring for operating mode SG (safety door)

4.5

Testing with operating mode 1 AOPD and 2 AOPDs

The protective sensors (AOPDs) are monitored for

• Short-circuit with operating voltage (Vcc or GND)
• Electrical cross-circuit
• Optical cross-circuit or short-circuit

For this purpose, control outputs S11 and (after a delay) S21 are clocked.

4.6

Testing with operating mode ES and SG

The E-Stop and safety door switch is monitored for

• Short-circuit with operating voltage (Vcc or GND)
• Electrical cross-circuit

For this purpose, control outputs S11 and (after a delay) S21 are clocked as shown in the diagram below:

a

Test signal of MSI-TRMB at S11 and S21

Figure 4.5: Diagram showing clocking of control outputs S11 and S21

4.7

Start/restart interlock and contactor monitoring (EDM)

The start/restart interlock prevents automatic start-up of the system (e.g. if the protective field is again clear

or if an interruption in the voltage supply is restored). The operating personnel must make certain that no

people are present in the danger zone before the system is manually re-enabled.
The restart interlock is configured via the wiring.

The safety door monitoring switches must be closed so that the safety switching outputs (OSSD)

can close.

SG

S11

S12

S21

S22

S32

SG

The total delay time for a linked series of photoelectric sensors must be in the range from 0.5 ms

to 6.5 ms.

a

1 ms

200 ms

«
...
13
14
15
16
17
...
»

Содержание MSI-TRMB
















































Отзывы:

Нет отзывов