Lenovo ThinkSystem ST650 V2 Скачать руководство пользователя страница 58

Страница: 58 / 210

Complete the following steps:

1. If the DIMM configuration was changed prior to this failure, verify that the DIMMs are installed in the

correct population sequence.

2. Reseat the DIMM that failed POST memory test and the DIMMs on adjacent slots if populated. Boot

to F1 setup and enable the DIMM. Reboot the system.

3. If the DIMMs have been upgraded just prior to the issue, update UEFI to the latest version.

4. If the problem persists, collect Service Data logs.

5. Contact Lenovo Support.

•

FQXSPMA0005N: Subsystem [MemoryElementName] has insufficient memory for operation.

This message is for the use case when an implementation has detected that the usable Memory is
insufficient for operation.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Memory
SNMP Trap ID: 41
CIM Prefix: PLAT CIM ID: 0132

User Action:

Complete the following steps:

1. Ensure one or more DIMMs are installed in the server.

2. Resolve persistsing memory errors if they are present.

3. If no memory fault is recorded in the logs, verify that all DIMM connectors are enabled using the

Setup utility or the OneCLI utility.

4. Reseat all DIMMs, ensuring that DIMMs are installed in the correct population sequence according to

the service information for this product.

5. Clear CMOS memory on system board by reseating CMOS battery. Note that all firmware settings will

revert to default.

6. Reflash UEFI firmware.

7. If problem persists, collect Service Data log.

8. Contact Lenovo Support.

•

FQXSPMA0007L: Scrub Failure for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName].

This message is for the use case when an implementation has detected a Memory Scrub failure.

Severity: Error
Serviceable: Yes
Automatically notify Support: Yes
Alert Category: Critical - Memory
SNMP Trap ID: 41
CIM Prefix: PLAT CIM ID: 0136

User Action:

Complete the following steps:

1. Ensure one or more DIMMs are installed in the server.

2. Resolve persistsing memory errors if they are present.

ThinkSystem ST650 V2 Messages and Codes Reference

Содержание ThinkSystem ST650 V2



















































































































































































































Результаты поиска

Содержание ThinkSystem ST650 V2

Отзывы:

Похожие инструкции для ThinkSystem ST650 V2

Бренды по названию

Популярные бренды

Lenovo ThinkSystem ST650 V2, Справочник

Результаты поиска

Содержание ThinkSystem ST650 V2

Отзывы:

Похожие инструкции для ThinkSystem ST650 V2

Бренды по названию

Популярные бренды