Lenovo ThinkSystem ST650 V2 Скачать руководство пользователя страница 31

Страница: 31 / 210

•

FQXSPBR4008I: Management Controller [arg1]: Configuration restoration from a file by user [arg2]

failed to start.

This message is for the use case where a user restores a Management Controller configuration from a file
and the restoration fails to start.

Severity: Error
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0138

User Action:

Complete the following steps until the problem is solved:

1. Check if password for encrypted backup config file is correct.

2. Retry the operation.

3. AC cycle the system.

4. If problem persists, collect Service Data log.

5. Contact Lenovo Support.

•

FQXSPBT0007I: No bootable media available for system [ComputerSystemElementName].

This message is for the use case when an implementation has detected a System with No Bootable
Media.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID:
CIM Prefix: PLAT CIM ID: 0286

User Action:

Ensure that the bootable media is installed correctly.

•

FQXSPCA0002M: Numeric sensor [NumericSensorElementName] going low (lower critical) has

asserted.

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has asserted.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Fan Failure
SNMP Trap ID: 11
CIM Prefix: PLAT CIM ID: 0480

User Action:

Complete the following steps:

1. Ensure all fans are installed correctly.

2. Reseat the fan.

3. If problem persists, collect Service Data log.

Chapter 2

XClarity Controller events

Содержание ThinkSystem ST650 V2



















































































































































































































Результаты поиска

Содержание ThinkSystem ST650 V2

Отзывы:

Похожие инструкции для ThinkSystem ST650 V2

Бренды по названию

Популярные бренды

Lenovo ThinkSystem ST650 V2, Справочник

Результаты поиска

Содержание ThinkSystem ST650 V2

Отзывы:

Похожие инструкции для ThinkSystem ST650 V2

Бренды по названию

Популярные бренды