Lenovo ThinkSystem ST650 V2 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 210

background image

1. Check the event log of system management module and XClarity Controller for any fan or cooling

related issues.

2. Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in

place, clean, and correctly installed.

3. Make sure that the room temperature is within operating specifications.

4. If the problem persists and there are no other DIMMs with the same indication, replace the DIMM.

•

FQXSPMA0011G: Memory Logging Limit Reached for [PhysicalMemoryElementName] on

Subsystem [MemoryElementName].

This message is for the use case when an implementation has detected that the Memory Logging Limit
has been Reached.

Severity: Warning
Serviceable: Yes
Automatically notify Support: Yes
Alert Category: Warning - Memory
SNMP Trap ID: 43
CIM Prefix: PLAT CIM ID: 0144

User Action:

Complete the following steps:

1. If the server has recently been installed, moved, serviced, or upgraded, verify that the DIMM is

properly seated and visually verify that there is no foreign material in any DIMM connector on that
memory channel. If either of these conditions is found, correct and retry with the same DIMM. (Note:
The event Log might contain a recent FQXSFMA0011I event denoting detected change in DIMM
population that could be related to this problem.)

2. If no problem is observed on the DIMM connectors or the problem persists, replace the DIMM

identified by LightPath and/or event log entry.

3. If problem recurs on the same DIMM connector, replace the other DIMMs on the same memory

channel.

4. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this

memory error.

5. If problem recurs on the same DIMM connector, inspect connector for damage. If damage is found or

problem persists, collect Service Data log.

6. Contact Lenovo Support.

•

FQXSPMA0012M: An Over-Temperature Condition has been detected on the

[PhysicalMemoryElementName] on Subsystem [MemoryElementName].

This message is for the use case when an implementation has detected an Over Temperature Condition
for Memory that has been Detected.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Temperature
SNMP Trap ID: 0
CIM Prefix: PLAT CIM ID: 0146

User Action:

Complete the following steps until the problem is solved:

1. Check the event log of XClarity Controller (XCC) for any fan or cooling related issues.

56

ThinkSystem ST650 V2 Messages and Codes Reference

«
...
58
59
60
61
62
...
»

Содержание ThinkSystem ST650 V2



















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkSystem ST650 V2

Бренд: Xerox Страницы: 220

Бренд: Xerox Страницы: 28

DocuPrint 100MX

Бренд: Xerox Страницы: 2

HS21 XM BLADECENTER - L5408 FOR SPEC CPU2006

Бренд: IBM Страницы: 1

SUPERSERVER 8045C-3R

Бренд: Supermicro Страницы: 118

UniServer T1100 G3

Бренд: H3C Страницы: 138

Бренд: 7thSense Страницы: 28

ZPS3611 - QUICK

Бренд: Zonet Страницы: 1

Бренд: Brocade Communications Systems Страницы: 176

Бренд: HIKVISION Страницы: 31

Aspire EASYSTORE H341

Бренд: Acer Страницы: 59

Aspire EASYSTORE H341

Бренд: Acer Страницы: 74

Aspire EasyStore Series

Бренд: Acer Страницы: 148

Aspire easyStore H340

Бренд: Acer Страницы: 68

Altos EasyStore

Бренд: Acer Страницы: 169

Aspire easyStore H340

Бренд: Acer Страницы: 148

Altos EasyStore

Бренд: Acer Страницы: 7

PowerEdge 400SC

Бренд: Dell Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды