Lenovo ThinkSystem ST650 V2 Скачать руководство пользователя страница 26

Страница: 26 / 210

Table 2. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSPBR4008I

Management Controller [arg1]: Configuration restoration from a file by
user [arg2] failed to start.

Error

FQXSPCA0002M

Numeric sensor [NumericSensorElementName] going low (lower
critical) has asserted.

Error

FQXSPCA0009M

Numeric sensor [NumericSensorElementName] going high (upper
critical) has asserted.

Error

FQXSPCA0011N

Numeric sensor [NumericSensorElementName] going high (upper
non-recoverable) has asserted.

Error

FQXSPCA0017M

Sensor [SensorElementName] has transitioned to critical from a less
severe state.

Error

FQXSPCA0019N

Sensor [SensorElementName] has transitioned to non-recoverable
from a less severe state.

Error

FQXSPCR0001N

Sensor [SensorElementName] has transitioned to non-recoverable
from a less severe state.

Error

FQXSPEA0002M

Sensor [SensorElementName] has transitioned to critical from a less
severe state.

Error

FQXSPFW0000N

The System [ComputerSystemElementName] encountered a POST
Error.

Error

FQXSPFW0001N

Firmware BIOS (ROM) corruption was detected on system
[ComputerSystemElementName] during POST.

Error

FQXSPFW0002N

The System [ComputerSystemElementName] encountered a firmware
hang.

Error

FQXSPIO0001L

The connector [PhysicalConnectorElementName] has encountered a
configuration error.

Error

FQXSPIO0003N

A diagnostic interrupt has occurred on system
[ComputerSystemElementName].

Error

FQXSPIO0004L

A bus timeout has occurred on bus [SensorElementName].

Error

FQXSPIO0006N

A software NMI has occurred on system
[ComputerSystemElementName].

Error

FQXSPIO0007N

A PCI PERR has occurred on system
[ComputerSystemElementName].

Error

FQXSPIO0008N

A PCI SERR has occurred on system
[ComputerSystemElementName].

Error

FQXSPIO0011N

An Uncorrectable Error has occurred on [SensorElementName].

Error

FQXSPIO0013N

A Fatal Bus Error has occurred on bus [SensorElementName].

Error

FQXSPIO0015M

Fault in slot [PhysicalConnectorSystemElementName] on system
[ComputerSystemElementName].

Error

FQXSPMA0002N

Configuration Error for [PhysicalMemoryElementName] on Subsystem
[MemoryElementName].

Error

FQXSPMA0005N

Subsystem [MemoryElementName] has insufficient memory for
operation.

Error

FQXSPMA0007L

Scrub Failure for [PhysicalMemoryElementName] on Subsystem
[MemoryElementName].

Error

ThinkSystem ST650 V2 Messages and Codes Reference

Содержание ThinkSystem ST650 V2



















































































































































































































Результаты поиска

Содержание ThinkSystem ST650 V2

Отзывы:

Похожие инструкции для ThinkSystem ST650 V2

Бренды по названию

Популярные бренды

Lenovo ThinkSystem ST650 V2, Справочник

Результаты поиска

Содержание ThinkSystem ST650 V2

Отзывы:

Похожие инструкции для ThinkSystem ST650 V2

Бренды по названию

Популярные бренды