Lenovo ThinkSystem ST650 V2 Скачать руководство пользователя страница 136

Страница: 136 / 210

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0035

User Action:

Information only; no action is required.

•

FQXSPUP4002I: Flash of [arg1] from [arg2] failed for user [arg3].

This message is for the use case where a user has not flashed the firmware component from the interface
and IP address due to a failure.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0036

User Action:

Information only; no action is required.

•

FQXSPUP4003I: [arg1] firmware mismatch internal to system [arg2]. Please attempt to flash the

[arg3] firmware.

This message is for the use case where a specific type of firmware mismatch has been detected.

Severity: Error
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0042

User Action:

Complete the following steps until the problem is solved:

1. AC cycle the system.

2. Reflash XCC/BMC firmware to the latest version.

3. NOTE: Some cluster solutions require specific code levels or coordinated code updates. If the device

is part of a cluster solution, verify that the latest level of code is supported for the cluster solution
before you update the code.

4. If problem persists, collect Service Data log.

5. Contact Lenovo Support.

•

FQXSPUP4004I: XCC firmware mismatch between nodes/servers [arg1] and [arg2]. Please attempt

to flash the XCC firmware to the same level on all nodes/servers.

A mismatch of XCC firmware has been detected between nodes/servers

Severity: Error
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other

132

ThinkSystem ST650 V2 Messages and Codes Reference

Содержание ThinkSystem ST650 V2



















































































































































































































Результаты поиска

Содержание ThinkSystem ST650 V2

Отзывы:

Похожие инструкции для ThinkSystem ST650 V2

Бренды по названию

Популярные бренды

Lenovo ThinkSystem ST650 V2, Справочник

Результаты поиска

Содержание ThinkSystem ST650 V2

Отзывы:

Похожие инструкции для ThinkSystem ST650 V2

Бренды по названию

Популярные бренды