Lenovo ThinkSystem SR650 V2 Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 212

background image

Table 3. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSFPU4033F

TPM Firmware recovery is in progress. Please DO NOT power off or
reset system.

Warning

FQXSFPU4035M

TPM Firmware recovery failed. TPM chip may be damaged.

Warning

FQXSFPU4040M

TPM selftest has failed.

Warning

FQXSFPU4043G

TPM Firmware update aborted. System is rebooting...

Warning

FQXSFPU4050G

Failed to update TPM Firmware.

Warning

FQXSFPU4051G

Undefined TPM_POLICY found

Warning

FQXSFPU4052G

TPM_POLICY is not locked

Warning

FQXSFPU4053G

System TPM_POLICY does not match the planar.

Warning

FQXSFPU4054G

TPM card logical binding has failed.

Warning

FQXSFPU4057I

Secure boot variable is being accessed with an unauthorized
password, reset the system immediately to recover.

Warning

FQXSFPU4058I

Secure Boot Setting is changed from enabled to disabled

Warning

FQXSFPW0001L

CMOS has been cleared.

Warning

FQXSFSM0002N

Boot Permission denied by Management Module: System Halted.

Warning

FQXSFSM0003N

Timed Out waiting on boot permission from Management Module:
System Halted.

Warning

FQXSFSM0004M

An XCC communication failure has occurred.

Warning

FQXSFSR0001M

[arg1] GPT corruption detected, DiskGUID: [arg2]

Warning

FQXSFSR0003G

The number of boot attempts has been exceeded. No bootable
device found.

Warning

FQXSFTR0001L

An invalid date and time have been detected.

Warning

FQXSFDD0004M

DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required
Controller.

Error

FQXSFDD0012K

SATA Hard Drive Error: [arg1].

Error

FQXSFIO0005M

An intra-board UPI failure has been detected on the link between
processor [arg1] port [arg2] and processor [arg3] port [arg4].

Error

FQXSFIO0006M

An inter-board UPI failure has been detected on the link between
processor [arg1] port [arg2] and processor [arg3] port [arg4].

Error

FQXSFIO0007M

An error has been detected by the IIO on Bus [arg1]. The value of
Global Fatal Error Status register is [arg2]. The value of Global Non-
Fatal Error Status register is [arg3]. Please check error logs for
additional downstream device error data.

Error

FQXSFIO0010M

An Uncorrectable PCIe Error has Occurred at Bus [arg1] Device [arg2]
Function [arg3]. The Vendor ID for the device is [arg4] and the Device
ID is [arg5]. The physical [arg6] number is [arg7].

Error

FQXSFIO0011M

A PCIe parity error has occurred on Bus [arg1] Device [arg2] Function
[arg3]. The Vendor ID for the device is [arg4] and the Device ID is
[arg5]. The Physical slot number is [arg6].

Error

.

139

«
...
141
142
143
144
145
...
»

Содержание ThinkSystem SR650 V2





















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkSystem SR650 V2

Бренд: IBM Страницы: 438

Бренд: TYAN Страницы: 109

Бренд: Vxl Страницы: 2

Бренд: NTI Страницы: 35

Бренд: FS Страницы: 91

Бренд: Epson Страницы: 28

EpsonNet 802.11b

Бренд: Epson Страницы: 30

Stylus C80WN - Ink Jet Printer

Бренд: Epson Страницы: 1

Бренд: Epson Страницы: 258

Бренд: Epson Страницы: 280

Бренд: Acnodes Страницы: 1

Бренд: Acksys Страницы: 24

Бренд: ASUSTOR Страницы: 12

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

NetNumen U31 R06

Бренд: Zte Страницы: 128

Бренд: Promise Technology Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды