Lenovo ThinkSystem SR650 V2 Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 212

background image

•

FQXSFIO0013I: The device found at Bus [arg1] Device [arg2] Function [arg3] could not be

configured due to resource constraints. The Vendor ID for the device is [arg4] and the Device ID is
[arg5]. The physical slot number is [arg6].

Severity: Warning

User Action:

Complete the following steps:

1. If this PCIe device and/or any attached cables were recently installed, moved, serviced or upgraded,

reseat adapter and any attached cables.

2. Check Lenovo support site for any applicable service bulletin or UEFI or adapter firmware update

that applies to this error.(NOTE: It may be necessary to disable unused option ROMs from UEFI F1
setup, OneCLI utility, or using adapter manufacturer utilities so that adapter firmware can be
updated.)

3. Move the adapter to a different slot. If a slot is not available or error recurs, replace the adapter.

4. If the problem persists, collect Service Data logs.

5. Contact Lenovo Support.

•

FQXSFIO0014J: A bad option ROM checksum was detected for the device found at Bus [arg1]

Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The
physical slot number is [arg6].

Severity: Error

User Action:

Complete the following steps:

1. If thisPCIe device and/or any attached cables were recently installed, moved, serviced or upgraded.

Reseat adapter and any attached cables.

2. Move adapter to a different system slot, if available.

3. Check Lenovo support site for any applicable service bulletin or UEFI or adapter firmware update

that applies to this error.

Note:

It may be necessary to configure slot to Gen1 or to use special utility software so that adapter

firmware can be upgraded. Gen1/Gen2 settings can be configured via F1 Setup -> System Settings
-> Devices and I/O Ports ->PCIe Gen1/Gen2/Gen3 Speed Selection, or the OneCLI utility.

4. If the problem persists, collect Service Data logs.

5. Contact Lenovo Support.

•

FQXSFIO0015I: IFM: System reset performed to reset adapters.

Severity: Info

User Action:

Information only; no action is required.

•

FQXSFIO0016M: IFM: Reset loop avoided - Multiple resets not allowed.

Severity: Warning

User Action:

Complete the following steps:

1. Update all firmware (including adapter firmware) to the latest levels.

2. If problem persists escalate to the next level of support.

•

FQXSFIO0017M: IFM: Error communicating with the XCC - IFM may not be deployed correctly.

.

147

«
...
149
150
151
152
153
...
»

Содержание ThinkSystem SR650 V2





















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkSystem SR650 V2

Бренд: QNAP Страницы: 39

Бренд: sysmik Страницы: 2

ANR-C62-N1 Series

Бренд: Acrosser Technology Страницы: 57

Бренд: Thecus Страницы: 130

Бренд: CNET Страницы: 2

8676 - Eserver xSeries 335

Бренд: IBM Страницы: 172

Бренд: Rohde & Schwarz Страницы: 126

PCS400R Pro:Centric

Бренд: LG Страницы: 57

Бренд: LG Страницы: 104

Pro:Centric PCS200S

Бренд: LG Страницы: 40

Бренд: LG Страницы: 6

PCS500R Pro:Centric

Бренд: LG Страницы: 70

Бренд: LG Страницы: 24

Centric PCS150R Pro

Бренд: LG Страницы: 35

Centric PCS200R Pro

Бренд: LG Страницы: 384

Бренд: Sony Страницы: 8

BSV-M1 - StorStation NAS Server

Бренд: Sony Страницы: 58

Бренд: TAG Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды