Leguan 135 NEO Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 66

background image

37

Handling of fuel and oil products

When handling fuel and oil products, bear in mind:

-

Do not let any oil leak on the ground.

-

Use oil qualities recommended by the manufacturer. Do not mix different oil types and/or
brands with one another.

-

When handling oil, always wear appropriate protective equipment.

-

Before refuelling, always stop the combustion engine / electric motor and disconnect from
mains current.

-

Only use fuels recommended by the engine manufacturer. Do not mix any additives with the
fuel.

-

If fuel or oil gets into the eyes, mouth or open wound, clean it immediately with a lot of water
or designated fluid and call a doctor.

Check hydraulic hoses and components only when the engine is stopped and with pressure
released from the hydraulic system. Do not operate the machine if you have noticed faults or
leaks in the hydraulic system. Ejection of hydraulic fluid can cause burns or penetrate the skin
and cause serious injuries. Consult a doctor immediately if hydraulic fluid penetrates your skin.
Wash any body part that has come in contact with hydraulic oil carefully with water and soap.
Hydraulic oil is also harmful to the environment

–

prevent oil leakages. Only use hydraulic oil

types approved by the manufacturer.

Never handle pressurised hydraulic components, because
in case of failure on a fitting or component, a spray of high-
pressure hydraulic fluid can cause the machine to tip over
and result in serious injuries. Do not operate the machine if
you have noticed a fault in the hydraulic system.

Check hydraulic hoses for any cracks and wear. Monitor the hoses for wear and stop operation
if the outer layer of any hose has worn out. Check routing of the hoses adjust the hose clamps if
necessary to

prevent chafing. The hose’s expiry date is marked on it. After this date, the

component must be replaced. If any signs of a leak are observed, place a piece of cardboard
underneath the suspected component to determine the source.

If you find a fault, operation of the access platform must be stopped immediately and the hose
or the component must be replaced. Contact the Leguan service.

«
...
35
36
37
38
39
...
»

Содержание 135 NEO



































































Отзывы:

Нет отзывов

Похожие инструкции для 135 NEO

Бренд: H3C Страницы: 8

Бренд: Jefferson Страницы: 24

Бренд: Baier Страницы: 20

Бренд: ATD Tools Страницы: 24

Бренд: Simplex Страницы: 40

Бренд: W&T Страницы: 72

Бренд: Omega Страницы: 16

Бренд: STAYER WELDING Страницы: 56

Бренд: Uni-Mig Страницы: 16

Бренд: Magneti Marelli Страницы: 44

Бренд: JAMO Страницы: 18

WALLACE & TIERNAN SFC SC

Бренд: Evoqua Страницы: 82

Бренд: Thiele Страницы: 5

Бренд: iWeld Страницы: 90

Power2 S-MAG 180

Бренд: STAMOS Страницы: 282

Бренд: National Instruments Страницы: 4

WeldForce WF-205MST

Бренд: Weldclass Страницы: 80

Бренд: Migatronic Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды