manualshive.com logo in svg

Larson Davis HVM100, Руководство пользователя

Поделиться
Скачать
Larson Davis HVM100 Скачать руководство пользователя страница 133

4/11/03

C-1

A P P E N D I X

C

Serial Interface Commands

The HVM100 is equipped with a serial port for communica-
tions with any standard RS-232 device. The most common
use for this interface would be to either print, or to create a
custom software program that can interface with the
HVM100. The following is a list of commands and their
descriptions to assist a programmer in communicating with
the HVM100.

Setup and Query Commands

The setup/query commands are used to control the settings
and query the status of the HVM100 parameters. The first 20
commands (S1 - S19, and Q1 - Q19) are reserved for system
parameters. System parameter settings remain the same
regardless of the operating mode. The remaining commands
(S20 - S99, and Q20 - Q99) are for mode specific parame-
ters. Mode specific parameter selections can vary based on
the selected operating mode.

Setup commands can be sent at any time. If the HVM100 is
running, and changing the parameter requires a reset, then
the setup command will cause the instrument to automati-
cally stop, reset, change the parameter setting and start run-
ning again. Query commands do not require a stop and reset
of the HVM100.

Syntax for setup commands

The syntax for a setup command is Snn,i. The nn specifies
the number of the parameter and ‘i’ is the desired setting.

Содержание HVM100















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды