manualshive.com logo in svg

Larson Davis HVM100, Руководство пользователя

Поделиться
Скачать
Larson Davis HVM100 Скачать руководство пользователя страница 100

9-6

HVM100 User Manual

4/11/03

AC/DC Output Connector

AC output is useful for frequency analysis by an external
analyzer or for recording in a tape recorder. The DC output
is useful for a chart recorder, or to measure the voltage pro-
portional to the RMS or peak value.

The DC output is updated according to the averaging time. If
the averaging time is set to slow, the signal on the DC output
pin for the selected channel will be updated once per second.
If the averaging time is set to 60 seconds, the signal on the
DC output pin for the selected channel will be updated once
every 60 seconds.

The AC output will produce a signal from 0 - 0.5 Volt RMS.

The scale of the DC output is typically 5 mV/dB. The level
typically varies between 0 Vdc to +1.0 Vdc.

Example:

Chart recorder output, monitoring the

DC output, with an averaging time of 60 seconds.

Содержание HVM100















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды