Lanier AP4510 Скачать руководство пользователя страница 29

Страница: 29 / 424

Installing Options

DDDD

Remove the two screws locking
the printer board.

The screws are needed to lock the
printer board afterwards.

EEEE

Remove the two screws locking
the Printer Hard Disk cover next
to the printer board.

The screws are needed to lock the
cover afterwards.

FFFF

Align the Printer Hard Disk with
the top and bottom rails , and then
insert the Printer Hard Disk slow-
ly until it stops.

GGGG

Hold the handle, and carefully
pull out the printer board half-
way.

HHHH

Connect the bigger plug of the
power cord to the printer board.

IIII

Connect the connector to the
printer board.

Note

❒

Connect either side of the con-
nector.

AP3ENSetup-F-ricoh_FM.book Page 19 Friday, October 5, 2001 2:43 PM

Содержание AP4510





































































































































































































































































































































































































































Результаты поиска

Содержание AP4510

Отзывы:

Похожие инструкции для AP4510

Бренды по названию

Популярные бренды

Lanier AP4510, Руководство по установке

Результаты поиска

Содержание AP4510

Отзывы:

Похожие инструкции для AP4510

Бренды по названию

Популярные бренды