Lanier AP4510 Скачать руководство пользователя страница 144

Страница: 144 / 424

Troubleshooting

Low: Staples

The staples in the optional
Finisher SR730 is almost run
out.

Prepare a new staple car-
tridge.

Low: Toner

The toner is almost run out.

Prepare a new toner bottle.

Malfunction: Duplex Unit

An error has occurred in the
Duplex Unit.

Reinstall the Duplex Unit. If
the message appears again,
call your sales or service rep-
resentative.

Malfunction: Finisher

An error has occurred in the
optional Finisher SR730.

Reinstall the Finisher. If the
message appears again, call
your sales or service repre-
sentative.

Malfunction: LCT

An error has occurred in the
optional Large Capacity Tray.

Reinstall the Large Capacity
Tray. If the message appears
again, call your sales or serv-
ice representative.

Malfunction: Staple Unit

An error has occurred in the
staple unit in the Finisher
SR730.

Reinstall the staple unit. If the
message appears again, call
your sales or service repre-
sentative.

Malfunction: Tray #

An error has occurred in the
indicated tray.

#: tray number

First, turn the power switch
off and then on. Reinstall the
tray. If the message appears
again, call your sales or serv-
ice representative.

Mismatch: Paper Size

The paper size setting of the
tray differs from that of actual
paper size in the tray.

Load paper of the indicated
paper size into the paper tray
being used. See p.25 “Paper
and Other Media Supported
by This Printer”.

Mismatch: Paper Size and
Type

The paper size and type set-
ting of the tray differs from
that of actual paper type in the
tray.

Load paper of the indicated
paper size and type into the
paper tray being used. See
p.25 “Paper and Other Media
Supported by This Printer”.

Mismatch: Paper Type

The paper type setting of the
tray differs from that of actual
paper type in the tray.

Load paper of the indicated
paper type into the paper tray
being used. See p.25 “Paper
and Other Media Supported
by This Printer”.

Nearly Full: Waste Toner

The waste toner bottle is al-
most full of toner dust.

Call your sales or service rep-
resentative.

No Paper

There is no paper in the tray.

Load paper in the tray. See
p.33 “Loading Paper and Oth-
er Media”.

Messages

Description

Solution

Содержание AP4510





































































































































































































































































































































































































































Результаты поиска

Содержание AP4510

Отзывы:

Похожие инструкции для AP4510

Бренды по названию

Популярные бренды

Lanier AP4510, Руководство по установке

Результаты поиска

Содержание AP4510

Отзывы:

Похожие инструкции для AP4510

Бренды по названию

Популярные бренды