Lanier AP4510 Скачать руководство пользователя страница 155

Страница: 155 / 424

Removing Misfed Paper

CCCC

Open the lower vertical paper
feed cover.

DDDD

Remove the misfed paper.

EEEE

Close the lower vertical paper
feed cover.

FFFF

Open the upper vertical paper
feed cover.

Note

❒

If your printer is equipped with
the optional Large Capacity
Tray RT36, the upper vertical
paper feed cover is removed.

GGGG

Turn the blue knob A1 down-
wards.

HHHH

While lifting the blue lever A2 in
the right cover (

), remove the

misfed paper (

IIII

Open the Bypass Tray, and then
remove the misfed paper.

JJJJ

Close the covers in the following
order:

• The upper vertical paper feed

cover

• The right cover
• The Duplex Unit
• The Bypass Tray

TSPY140E

TAPY150E

TAPY110E

TAPY120E

Содержание AP4510





































































































































































































































































































































































































































Результаты поиска

Содержание AP4510

Отзывы:

Похожие инструкции для AP4510

Бренды по названию

Популярные бренды

Lanier AP4510, Руководство по установке

Результаты поиска

Содержание AP4510

Отзывы:

Похожие инструкции для AP4510

Бренды по названию

Популярные бренды