Lanier AP4510 Скачать руководство пользователя страница 111

Страница: 111 / 424

Loading Paper and Other Media

BBBB

Remove the rear guide by press-
ing the sides of it.

CCCC

Pull the standard paper tray (Tray
1), and then take the screwdriver
(

) from the tray.

DDDD

Remove the four screws inside of
the tray using the screwdriver.

EEEE

Re-position the side guides to
match the paper size you want to
load.

FFFF

Lock the side guides with the four
screws using the screwdriver.

GGGG

Align all four sides of the paper
stack and load it into the tray with
the print side up.

Important

❒

Confirm that the top of the stack
is not higher than the limit mark
inside the tray.

TAPY063E

TAPY041E

TAPY051E

TAPY062E

TAPY091E

Содержание AP4510





































































































































































































































































































































































































































Результаты поиска

Содержание AP4510

Отзывы:

Похожие инструкции для AP4510

Бренды по названию

Популярные бренды

Lanier AP4510, Руководство по установке

Результаты поиска

Содержание AP4510

Отзывы:

Похожие инструкции для AP4510

Бренды по названию

Популярные бренды