Lanier AP4510 Скачать руководство пользователя страница 267 | Manualshive

Страница: 267 / 424

background image

Configuring the Protocols

27

3

Configuring the Protocols

Configuring TCP/IP and IPP for Printing

These instructions are for configuring the Network Interface Board and Win-
dows NT to use the TCP/IP protocol and IPP.

Configuring the machine

Configure the machine to use the TCP/IP protocol.
• Make sure that the TCP/IP protocol is set to active. (The default is active.)
• Assign an IP address and make other settings required for using the TCP/IP

protocol.

Reference

For more information about how to make the above settings, see the Setup
Guide.
If DHCP is used to assign IP addresses, see p.92 “Using DHCP”.

Note

❒

After setting the IP address, use the ping command to make sure that it has
been correctly set.

A

Click

[

Start

]

, point to

[

Programs

]

, and then click

[

Command Prompt

]

.

B

Type the following: (Example IP address is 192.168.15.16)

C:\> ping 192.168.15.16

If the address has been configured correctly, the following message ap-
pears.

Reply from 192.168.15.16 : bytes=32 time<10ms TTL=32

If the address has been configured incorrectly, the following message ap-
pears.

Request timed out.

Configuring a Windows NT computer

These steps are for configuring a Windows NT computer to use the TCP/IP pro-
tocol.

AAAA

Open

[

Control Panel

]

, and then double-click the

[

Network

]

icon. Make sure

that “TCP/IP Protocol” is listed in the

[

Network protocols

]

box on the

[

Proto-

cols

]

tab.

Note

❒

If the TCP/IP protocol is not installed, click

[

Add

]

on the

[

Protocols

]

tab to

install it. For more information about installing the TCP/IP protocol, see
Windows NT Help.

«
...
265
266
267
268
269
...
»

Содержание AP4510









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AP4510

Бренд: Xerox Страницы: 168

Бренд: Xerox Страницы: 36

Бренд: Xerox Страницы: 64

Бренд: Xerox Страницы: 54

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 115

Бренд: GCC Technologies Страницы: 8

Бренд: Oki Страницы: 198

Бренд: SEWOO Страницы: 13

Бренд: Xerox Страницы: 6

634dte - X B/W Laser

Бренд: Lexmark Страницы: 148

Бренд: B-G Instruments Страницы: 2

Бренд: Oki Страницы: 109

imageRUNNER ADVANCE DX C7700 Series

Бренд: Canon Страницы: 127

Бренд: Canon Страницы: 146

Бренд: Epson Страницы: 7

LabelWorks Safety Kit

Бренд: Epson Страницы: 42

LASER PRINTER C3900DN

Бренд: Epson Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды