Lanier AP4510 Скачать руководство пользователя страница 377

Страница: 377 / 424

1. UNIX Configuration

This section explains how to set up a network printer and check the print status
using UNIX.

Limitation

❒

To print from a UNIX workstation, use the file that the printer supports.

Before Setup

Setting up can vary depending on the printing commands. Please make sure to
make the settings accordingly.

Using the lp/lpr commands

AAAA

Use the installation shell script to register the device option, as well as the
printer host name and the IP address.

⇒

p.2 “Using the Installation Shell Script”

BBBB

Start printing.

⇒

p.11 “Printing Method”

Using the rsh/rcp/ftp commands

AAAA

Edit the host file to register the printer host name and the IP address.

BBBB

Start printing.

⇒

p.11 “Printing Method”

Reference

See p.6 “After Executing Installation Shell Script” for host file editing.

Note

❒

If you cannot edit the host file, use the install shell script to register the host
name.

Содержание AP4510





































































































































































































































































































































































































































Результаты поиска

Содержание AP4510

Отзывы:

Похожие инструкции для AP4510

Бренды по названию

Популярные бренды

Lanier AP4510, Руководство по установке

Результаты поиска

Содержание AP4510

Отзывы:

Похожие инструкции для AP4510

Бренды по названию

Популярные бренды