
Page 23 of 60
2.2 Installation and leveling
The spindle moulder comes assembled except interchangeable spindle, fence assembly, dust chute, miter
gauge, clamp attachment and some other loose items.
Carefully remove machine from wooden shipping skid. For best shaping performance, locate spindle moulder
on a soild, level foundation.
With machine in position, check table surface left to right and front to back with a machine level.
If necessary, place metal shims under the corners of the machine to insure that the machine is level.
Check to be sure that all four corners of the machine are supported and fasten the machine to the floor using
foot (leveling) screws. Re-check to make sure table is level and re-adjust if necessary.
2.3 Grounding information and power connections
Before connecting your spindle moulder to the power source, be sure that the electric current of the power
source is of the same characteristics as the electrical system supplied with your machine.
Machine overcurrent protective device and power cable to be prepared by the user site:
SS-510 1PH
SS-510 3PH
SS-511 1PH
SS-511/512/513 3PH
PS-515/PS-515plus 3PH
KW (spindle motor)
1.5
2.2
3
1.5
2.2
3
3.75
3.75
5.5
7.5
3.75
5.5
7.5
Mains Fuse A
16
25
32
6
8
10
40
16
16
20
16
16
20
PVC Power cable mm
2
/PE 3.5 5.5 5.5 2
2
2
8
3.5
3.5
5.5
3.5 3.5
5.5
To connect power to the machine, proceed as follows:
1. Remove two screws (A) Fig.2.3, and remove terminal strip cover (B).
2. Remove clear plastic insulator (C) Fig.2.4 that covers the terminals.
3. Insert power line through opening (D) Fig.2.3, of terminal strip box (G).
4. And the wire bicolour combination GREEN-AND- YELLOW to PE-terminal.
5. Reassemble the clear plastic insulator that was removed in STEP 2 and the terminal strip cover that was
removed in STEP 1.
C
F
E
Fig. 2.3
Fig. 2.4
Fig. 2.5
《
CAUTION
》
The best work conditions for the machine is to furnish the right tension indicated on the motor
plate, however it can adapt itself to tensions superior or inferior in a tolerance field of +/-5%.(e.g. a machine
with a work tension of 380 volts has a tolerance field ranging from 360 to 400 volts).
2-2
Содержание S45T
