Label ETERNA 150 Series Скачать руководство пользователя страница 32

Страница: 32 / 68

Connect the battery to the connector J5 of the control unit ET‑LOGIC‑B.

Insert the battery charger card ET-BAT in connector J12 of the control unit ET-LOGIC-B.

To enable operation with battery, set the function F06 = ON, or set S04 = ON from the initial setup.

The battery charger automatically checks the battery charge level and displays a green and a red led (see table "LED SIGNALLING")

Operation

The device ET-BAT150 is enabled in case of mains power failure, allowing the automation ETERNA 150 to operate.

Battery life depends on various factors, on the number of manoeuvres carried out, on the weight of the leaf, on the external devices

connected, etc.

The charged battery can supply energy for approximately 10 continuous door opening/closing cycles.

IMPORTANT!

BATTERY TYPE: NiMH, 18V - 700mAh

LED SIGNALLING

SIGNALLED EVENTS

GREEN LED DL7

RED LED DL6

BATTERY DISCONNECTED

BATTERY CHARGING

BLINKING

OFF

BATTERY CHARGED WITH MAINS VOLTAGE

OFF

BATTERY LOW

OFF

BLINKING

BATTERY CHARGED WITHOUT MAINS VOLTAGE

OFF

WARNING

•

Periodically check battery efficiency

•

To allow recharging, the batteries must always be connected to the

electronic control unit

•

The equipment must be disconnected from the mains when

removing the batteries

•

In case of replacement, always use genuine batteries

•

Replacement must be performed by qualified personnel

•

Remove batteries from the equipment before its disposal

•

Batteries contain polluting substances; therefore they must be

disposed of in accordance with the provisions of local regulations

BATTERY

18V

BATTERY

CHARGER

ET-BAT

to connector J12 of the control unit ET-LOGIC-B

BATTERY

15) BATTERY-POWERED EMERGENCY OPENING DEVICE ET-BAT150

Содержание ETERNA 150 Series





































































Результаты поиска

Содержание ETERNA 150 Series

Отзывы:

Похожие инструкции для ETERNA 150 Series

Бренды по названию

Популярные бренды

Label ETERNA 150 Series, Руководство по установке

Результаты поиска

Содержание ETERNA 150 Series

Отзывы:

Похожие инструкции для ETERNA 150 Series

Бренды по названию

Популярные бренды