Control Sources
Descriptions of Control sources
25-6
76—79
MIDI 76—79
80—83
MIDI 80—83 (Ctl E—H)
84—90
MIDI 84—90
91
MIDI 91 (FXDep)
The MIDI specification defines this controller as External Effects Depth. If the FX
Mode parameter is set to Master, and the FX Channel parameter is set to a specific
MIDI channel, the K2vx will respond to this message when it is received on the FX
channel. It responds by adjusting the Wet/Dry mix of the current preset effect.
92—95
MIDI 92—95
96
MIDI 96 (DataInc)
This is defined as Data Increment. ItÕs intended to be assigned to a switch control.
When the control is on (value 127), the currently selected parameterÕs value will be
increased by one increment. This could be assigned to FootSw2, for example, to
scroll through the program list while in Program mode.
97
MIDI 97 (DataDec)
This is defined as Data Decrement. ItÕs intended to be assigned to a switch control.
When the control is on (value 127), the currently selected parameterÕs value will be
decreased by one increment.
123
MIDI 123 (Panic)
The K2vx always responds to this message by sending an All Notes Off and All
Controllers Off message on all 16 MIDI channels.
Main Control Source List
This list contains all but the last three control sources in the MIDI Control Source list. It also
contains the following control sources. All are local unless speciÞed as global.
32
Channel State (Chan St)
Chan St refers to whether any notes are currently active on a given MIDI channel.
Chan St switches on whenever a note is started, and switches off when a Note Off
has been received for each current note on that channel, even if notes are sustained.
33
Mono pressure (MPress)
This is the same as the MPress control source in the MIDI Control Source list, but
is assigned by entering 33 on the alphanumeric pad when used with a parameter
that takes its values from the Main Control Source list.
34
Bipolar mono pressure (BMPress)
This control source generates a control signal of -1 when the value of the control to
which itÕs assigned is at its minimum, and +1 when the control is at its maximum.
For example, if you had the MPress control assignment parameter assigned to send
BMPress, and you had Src1 on a program layerÕs PITCH page assigned to BM-
Press, with its depth parameter set to 1200 cents, then the layer would be trans-
posed down an octave when no pressure (value 0) was applied to your controllerÕs
keys (assuming it sends mono pressure). Maximum pressure (value 127) would
Содержание K2500RS
