Program Mode and the Program Editor
The Program Editor—Pages
6-13
Opaque
An opaque layer blocks all higher-numbered layers in its range, allowing only the opaque layer
to play. This is an easy way to change a small range of notes in a program, leaving the original
sound playing above and below the new sound. Just create a new layer (Layer 2), set its range
(say, C 3 to D 3), assign it the keymap you want, and set its Opaque parameter to On. Then
duplicate the original layer, so its number is higher than that of the new layer (the duplicate
layer is Layer 3). YouÕll now have a three-layer program. Delete Layer 1 (the original layer), and
the new Layer will become Layer 1, while the duplicated original layer becomes Layer 2. Now
the new layer will block out the original layer at the notes C 3ÐD 3.
Sustain Pedal (SusPdl)
When this parameter is on, the layer will respond to all sustain messages (MIDI 64) received by
the K2vx. When off, the current layer will ignore sustain messages.
Sostenuto Pedal (SosPdl)
When Sostenuto is on, the layer will respond to all sostenuto messages (MIDI 66) received by
the K2vx. When off, sostenuto messages are ignored by the layer.
Freeze Pedal (FrzPdl)
Activate or deactivate the layerÕs response to Freeze pedal messages (MIDI 69). The Freeze
pedal control causes all notes that are on to sustain without decay until the Freeze pedal control
goes off. If a note is already decaying, it will freeze at that level.
Ignore Release (IgnRel)
When on, the layer will ignore all Note Off messages received by the K2vx. This should be used
only with sounds that decay naturally, otherwise the sounds will sustain forever. When IgnRel
is off, the layer responds normally to Note Off messages.
This parameter can come in handy when your K2vx is slaved to a drum machine or sequencer,
which sometimes generates Note Ons and Note Offs so close together that the envelope doesnÕt
have time to play before the note is released. YouÕll also want to use this parameter when youÕre
playing staccato, and the sound youÕre playing has a long amplitude envelope. This parameter
should be used only with notes that eventually decay to silence. Sustaining sounds will sustain
forever.
Hold Through Attack (ThrAtt)
When on, this parameter causes all notes in the layer to sustain through the entire Þrst attack
segment of their amplitude envelopes, even if the notes have been released.
If you have a sound with a slow attack, or an attack thatÕs delayed with the delay control,
setting this parameter to On will make sure your notes reach full amplitude even if youÕre
playing fast. When set to Off, notes will release as soon as you release the note (generate a Note
Off). If the Þrst attack segment of the layerÕs amplitude envelope is very short, you probably
wonÕt notice a difference between values of On and Off.
Hold Until Decay (TilDec)
When on, this parameter causes all notes in the layer to sustain through all three attack
segments in their amplitude envelopes even if the notes have been released. Looped amplitude
envelopes will not loop, however, if the notes are released before reaching the end of the Þnal
attack segment. Notes will go into their normal releases if they are released after the envelope
has looped. When set to Off, notes will release as soon as a Note Off message is generated.
Содержание K2500RS
