Setup Mode and the Setup Editor
The Setup Editor
7-4
Pitch Bend (PBend)
The Pitch Bend parameter determines whether the currently selected zone of the currently
selected setup will receive the Pitch Bend message when your MIDI controllerÕs Pitch Wheel is
moved. This lets you use Pitch bend with some zones and not from others. Choose On to enable
the Pitch Wheel message in the current zone, or Off to disable it. This parameter is relevant only
if the Local Keyboard Channel parameter on the RECV page in MIDI mode is set to match the
MIDI channel youÕre using to transmit from your MIDI controller.
Program Change (PChng)
This enables or disables program change commands sent to the MIDI Out port when you select
setups from the K2vxÕs front panel or from your MIDI controller when the K2vx is in Quick
Access mode. If itÕs set to On, then the program numbers for the programs in the three zones
will be sent via MIDI when a setup is selected. When this parameter is set to Off, you can select
a setup to play on the K2vx, without changing the programs on MIDI devices receiving from
the K2vx.
Volume (V)
This parameter enables you to control the initial MIDI volume setting for each zone of the
current setup. When you call up a setup in Setup mode, the K2vx sends a MIDI volume control
signal on the each of the setupÕs MIDI channels. This sets the starting volume level for each
zone. Subsequent MIDI volume control signals sent to the setupÕs MIDI channels will affect the
volume normally. The Setting of the "V"parameter on the MIDI mode XMIT page (see page 10-
4) determines whether or not this parameter will have any effect.
The Remaining Parameters
A long list of values (the Control Source list) is available for each of the remaining six
parameters, which determine two things: how the K2vx responds to Mod Wheel, switch
pedal, continuous control pedal, data slider and mono pressure messages from your MIDI
controller, and how the K2vx remaps these messages to send to its own MIDI Out port. (See the
discussion of the Local Keyboard Channel parameter in Chapter 10.) Each zoneÕs assignments
are independent; you can assign a given control in one zone and not the others. While you
remain in Setup mode, the values you set for these parameters will override the conÞguration
of the XMIT page in MIDI mode.
The Setup Editor’s Soft Buttons
There are three soft buttonsÑName, Save, and DeleteÑfor basic library functions, and one for
dumping the whole setup as a MIDI System Exclusive message. The Set Range (SetRng) soft
button gives you a quick way to set the values for the LoKey and HiKey parameters for the
currently selected zone. Press this button, and the K2vx will prompt you to trigger the low note.
Press the Cancel soft button if you change your mind. Otherwise, trigger the note you want to
be the lowest in the current zone. When you trigger a note, the K2vx prompts you to trigger the
note to be the highest in the zone. When you trigger another note, the Setup Editor page
returns, and the notes you triggered will be recorded as the new values for the LoKey and
HiKey parameters. YouÕll notice that the higher of the two notes you triggered is entered as the
HiKey value, regardless of the order in which you triggered the two notes.
It’s Not Just for Editing Anymore
You might think that the Setup Editor is intended strictly for programming setups between gigs
or sessions. But itÕs convenient in performance situations, as well. All of the K2vxÕs
performance features function normally while the Setup Editor is active. You can make quick
changes to the current setupÑchoose a different lead sound, for example, or switch one zone to
a different MIDI channel to control one of the rack-mount synths at the studio. You can save
your changes if you want, or you can exit the Setup Editor without saving to restore your
original setups.
Содержание K2500RS
